Toshiba TDP-EX20U - Short Throw DLP Projector Посібник користувача - Сторінка 15
Переглянути онлайн або завантажити pdf Посібник користувача для Проектор Toshiba TDP-EX20U - Short Throw DLP Projector. Toshiba TDP-EX20U - Short Throw DLP Projector 50 сторінок. Toshiba tdp-ex20u: specifications
Також для Toshiba TDP-EX20U - Short Throw DLP Projector: Технічні характеристики (2 сторінок)
Друкувати сторінку
Basic operations
Turn on the power.
1
Turn on the power by following the instructions in "Turning the power on"
2
Select the language and the lamp power (When using the
first time).
When the projector is used for the first time after purchase, the start menu for language
(to display the menus and messages on the screen) and lamp power selection and
configuration is displayed in English. (If the screen is out of focus, adjust it according to
the step
6
.)
Use the
,
,
or
button to select the desired language and
1
press the
button.
English
French
German
Italian
Spanish
Portuguese
Russian
Swedish
Turkish
Message for setup confirmation is displayed in a selected language.
Then, the menu for lamp power selection and configuration is displayed. It is
automatically set as Standard. To change the setting, follow the step
Use the
or
button to select the lamp power and press the
2
button.
The lamp power, if selected, will be toggled without pressing the
automatically disappears in a few seconds.
Notes
•
When the projector is turned on the next time, the start menu does not appear upon
startup. However, if [Reset all] is executed from the Default setting 2 menu
the start menu will be displayed the next time when the power is turned on.
•
The language can also be set via the Display setting menu
via the Default setting 2 menu
p.44
•
This owner's manual assumes that English has been selected.
3
Activate the connected device.
Turn on and start the connected device such as a computer.
4
Press the INPUT button.
An image of the connected equipment is projected.
Each time you press the INPUT button, it switches to the input of the connected
equipment that is outputting video signals.
p.26
.
Polish
Japanese
Norwegian
Chinese (simplified)
Finnish
Chinese (traditional)
Czech
Korean
Hungarian
Indonesian
Greek
Danish
Dutch
Rumanian
2
.
button. The display
p.40
and Lamp power
.
28
Notes
•
When [Auto input search] is set to [Off] in the Default setting 1 menu
(factory setting is [On]), the Input select menu appears if you press the INPUT
button
p.43
•
If no signal is being output from the connected equipment, pressing the INPUT
button does not change the input and "There is no other input signal." will appear.
5
Projector placement angle adjustments
The placement angle and the height of the projected image can be adjusted by the
foot adjuster.
Lift up the front of the projector to
1
the desired angle, then press the foot
adjuster release button.
The foot adjuster extends. Release the button
to lock the position.
To fine adjust the angle, twist the foot
2
adjuster.
To adjust the horizontal angle, use the
3
right and left tilt adjusters.
•
To stow the foot adjuster, hold up the projector while pressing the foot adjuster
release button, then slowly lower the projector.
Note
•
When [Auto keystone] is set to [On] in the Default setting 1 menu, the keystone
distortion will automatically be corrected based on the projector placement angle. If
you do not desire the automatic keystone correction, set [Auto keystone] to [Off].
6
Adjusting the screen size and focus
If you wish to make the screen size
1
smaller, use the ZOOM button to
p.44
,
adjust the screen size.
Use the focusing lever to adjust the
2
focus.
Adjusting the volume with the
7
buttons
The speaker volume can be adjusted when an audio signal is being input.
.
Control panel
29
p.43
Focusing lever