Toshiba TDP-S80 Посібник користувача - Сторінка 17

Переглянути онлайн або завантажити pdf Посібник користувача для Проектор Toshiba TDP-S80. Toshiba TDP-S80 25 сторінок. Svga / with document camera
Також для Toshiba TDP-S80: Посібник користувача (25 сторінок)

Друкувати сторінку
Toshiba TDP-S80 Посібник користувача
Using the menu (Continued)

The default setting menu

This menu shows placement status and other settings.
Item
Projection
Sets projection mode in accordance with Placement Style.
mode
(Standard)
No signal
Set the timer to wait for the power to be turned off after signal input stops.
power off
Press
. Switch with
Off (not turned off)/1 min./5 min./10 min./30 min./60 min.
Auto input
Set whether the input with signals is only selected or not.
search
Power on
Sets whether to turn on the power when the ON/STANDBY button is pressed
(Manual), or when the power cord is plugged in (Auto). Manual
Lamp power
[Note 1]
Sets the lamp power.
Fan mode
[Note 2]
Sets the cooling fan speed.
Reset all
Press
.
Resets all adjustments and settings to their factory settings.
Notes
1: When Lamp power is set to Low, the screen becomes a little darker, but the cooling fan noise gets
quieter. This setting will be cleared when you turn the power off.
2: Setting [Fan mode] to [High] increases the cooling fan speed. Set this option to use the projector,
for example, at high altitude (over 1,500 meters above sea level).
Notes
• Note that in the event of a power outage but the power is restored afterwards, the projector
power will come on if Power on is set to Auto, and the power cord is plugged in.
• When you turn off the projector even if Power on is set to Auto, you must press the ON/
STANDBY button to turn the power off.
Description
p.20
(Mounted
(Rear mounted
(Rear)
from ceiling)
from ceiling)
and
.
On
Low
Standard
Standard
Yes
32

Displaying Information (Status display)

This displays information about the input signal, lamp use time, etc.
Item
Input
Mode name
H-resolution
V-resolution
H-frequency
Off
V-frequency
Sync
Signal format
Auto
Video mode
Lamp time
Lamp reset count The count for lamp replacement
High
Total time
Version
No
Notes
1: The mode of supported RGB signals
2: Same as the refresh rate of the computer signal.
3: Sync signal polarity shown as P (positive) or N (negative) for [H/V].
4: Displays [Lamp time] as a measure of when the lamp should be replaced. (Cannot be used as
a counter of guaranteed lamp time.) When the displayed time approaches 2,000 hours, consult
with a store about getting a TLPLW5 replacement lamp (sold separately) prepared.
5: [Version] shows the version of the projector's internal control program. This version is referred
to for customer service, etc.
Note
• The displayed information will not be refreshed if the status changes. To refresh the
information, dismiss the display, then display it again.
"Yes": displayed, "No": not displayed
Description
Computer Y/P
Input source name
Yes
RGB input mode
[Note 1]
Yes
Horizontal resolution (in dots)
Yes
Vertical resolution (in dots)
Yes
Horizontal sync frequency
Yes
[Note 2]
Vertical sync frequency
Yes
Sync signal polarity
[Note 3]
Yes
Y/P
/P
signal format
No
B
R
Color method of video signal
No
Time of lamp use
[Note 4]
Yes
Yes
The total time that this projector is used
Yes
Firmware version
[Note 5]
Yes
p.45
is shown.
33
Video
/P
Camera
B
R
S-video
Yes
Yes
Yes
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
Yes
No
No
No
Yes
No
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes