Toshiba TDP-T350 - XGA DLP Projector Посібник користувача - Сторінка 15
Переглянути онлайн або завантажити pdf Посібник користувача для Проектор Toshiba TDP-T350 - XGA DLP Projector. Toshiba TDP-T350 - XGA DLP Projector 31 сторінка. Tdp-t250u user's guide
Друкувати сторінку
Basic operations
1
Turn on the power.
Turn on the power by following the instructions in "Turning the power on"
2
Select the language and the lamp power (When using the
first time).
When the projector is used for the first time after purchase, the start menu for lan-
guage (to display the menus and messages on the screen) and lamp power selection
and configuration is displayed in English. (If the screen is out of focus, adjust it
according to the step
.)
6
q Use the
or
button to select the
desired language and press the
Message for setup confirmation is displayed in a
selected language.
Then, the menu for lamp power selection and
configuration is displayed. It is automatically set as
Standard. To change the setting, follow the step w.
w Using the
or
button, select the lamp
power and press the
button.
The lamp power, if selected, will be toggled without
pressing the
button. The display automatically
disappears in a few seconds.
Notes
• When the projector is turned on the next time, the start menu does not appear upon
startup. However, if "Reset all" is executed from the Default setting menu
start menu will be displayed the next time when the power is turned on.
• The language can also be set via the Display setting menu
via the Default setting menu
p.42
• This owner's manual assumes that English has been selected.
3
Activate the connected device.
Turn on and start the connected device such as a computer.
4
Press the INPUT button.
Each time you press the INPUT button, it switches to the input of the connected
equipment that is outputting video signals.
Notes
• When [Auto input search] is set to [On] in the Default setting menu
setting is [On]), the input is switched to the connected equipment that is outputting video
signals each time you press the INPUT button
• If no signal is being output from the connected equipment, pressing the INPUT button
does not change the input and "No input signal" will appear.
p.26
English
button.
French
German
Italian
Spanish
Portuguese
Russian
Swedish
Turkish
Polish
Japanese
Chinese (simplified)
Chinese (traditional)
Korean
p.42
and Lamp power
p.40
.
(factory
p.42
.
p.43
28
5
Projector placement angle adjustments
.
The placement angle and the height of the projected image can be adjusted by the foot
adjuster.
q Lift up the front of the projector to
the desired angle, then press the
foot adjuster release button.
The foot adjuster extends. Release the
button to lock the position.
w To fine adjust the angle, twist the
foot adjuster.
e To adjust the horizontal angle, use
the tilt adjuster.
To stow the foot adjuster, hold up the projector
while pressing the foot adjuster release button,
then slowly lower the projector.
6
Adjusting the screen size and focus
q Use the zooming lever to adjust the screen size.
w Use the focusing lever to adjust the focus.
7
Adjusting the volume with the
The speaker volume can be adjusted when an audio signal is being input.
, the
Notes
• Note that a lamp characteristics may rarely cause the brightness to fluctuate slightly.
• A lamp is consumable item. If used for extended periods, images will appear dark, and
the lamp could burn out. This is characteristic of a lamp, and is not malfunction. (The
lifetime of the lamp depends on conditions of use.)
• The DMD
TM
is made using extremely advanced technology, but there may be black spots
(pixels that do not light) or bright spots (pixels that are constantly lit) on the panel. Please
note that these are not malfunctions.
• Although this projector supports a wide range of RGB signals
supported by this projector (XGA) will be expanded or shrunk, which will affect image
quality slightly. To view high-quality images, it is recommended that the computer's
external output should be set to XGA resolution.
• With some models of computer having LCD displays or the like, displaying images
simultaneously on the projector and the monitor's display may prevent the images from
displaying properly. If this happens, turn off the computer's LCD display. For information
on how to turn off the LCD display, see the owner's manual of your computer.
• If no signal is being input from the connected equipment or signal input is stopped while
projecting, the "No signal" will appear.
• If a signal not supported by the projector is input, the "Unsupported signal" will appear.
• If an unavailable operation button is pressed, the
1
3
2
1
2
buttons
, any resolutions not
p.53
icon will appear.
29