Dimplex AC45N Інструкція з монтажу та експлуатації - Сторінка 3
Переглянути онлайн або завантажити pdf Інструкція з монтажу та експлуатації для Кондиціонер Dimplex AC45N. Dimplex AC45N 4 сторінки. Ac air curtains
Також для Dimplex AC45N: Інструкція (3 сторінок), Посібник користувача (4 сторінок), Посібник з монтажу та експлуатації (12 сторінок), Посібник із швидкого старту (19 сторінок), Посібник (20 сторінок)
Друкувати сторінку
Operation (AC3N, AC45N & AC6N models)
Switch on electricity supply
to the heater.
Switching
the
switch
marked ' I ' energises the
blower.
Select ' I ' and the smaller
switches marked '
' as re-
quired (see
Fig. 12).
Settings -
I
I +
I +
+
Operation
(AC3RN
model)
Switch on electricity supply
to the heater.
Select the switch position '
MAN ' for Manual Opera-
tion.
Select the switch position '
AUTO ' for Operation via
the remote control.
Select the desired heat output using the smaller switches
position ' ' (see
Fig. 13).
To operate the remote control you must first select 'AUTO' .
The heater may now be turned 'On' or 'Off' using the Remote
Control.
Settings -
MAN
AUTO
MAN +
MAN +
'AUTO' will default to 'OFF' if the remote control is not being
used.
The range of the Remote Control is 15 metres.
Note :
Repeated simultaneous switching of the 'ON' and 'OFF' but-
tons on the remote control may require resetting of the heater-
see 'Resetting AC3RN remote control'.
If the remote control becomes lost, switch off at the mains
supply for at least 30 seconds and select 'MAN' for Manual
Operation.
Remote Control (AC3RN model only)
Insert the 9 volt battery into the remote control.
Press either the ON or OFF button to check the operation of
the remote. The green light on the front of the remote control
will light.
Switch the heater to AUTO for automatic operation.
Press the ON button to activate the heater, and OFF to turn
off.
If the remote control does not operate the heater, first check
battery and then follow the instructions under 'Resetting
AC3RN remote control'.
: Blower only
: Half heat
: Full heat
MAN
AUTO
: Blower only
: Remote On/Off
: Half heat
+
: Full heat
Fig. 12
Resetting AC3RN remote
control
Switch the heater to auto-
matic operation, and ensure
the remote control is func-
tioning. (green light should
operate)
Insert a small non-metallic
pin (dia. less than 2mm e.g.
a toothpick or match) into the
hole shown in
Fig. 13
press the reset button. At the
same time press the ON but-
ton on the remote control.
Release the reset button on
the heater and the button on
the remote control at the
same time.
The heater is now pro-
grammed to operate with
this remote sender unit.
Note this method can be
used to program a number
of heaters to operate from a
single remote control.
Screws and rawl plugs for wall fixing the holster are provided
also.
Important Battery information.
Discard leaky batteries.
Dispose of batteries in the proper manner according to
Provincial and local regulations. Any battery may leak elec-
trolyte if mixed with a different battery type, if inserted
incorrectly, if all the batteries are not replaced at the same
time, if disposed of in a fire or if an attempt is made to
charge a battery not intended to be recharged.
reset
button
(AC3RN only)
green
neon light
ON button
OFF button
Fig. 14
and
wall-mounted
holster
The remote control may be placed
when not in use in the wall-
mounted holster provided (see
Fig. 15).
Fig. 14
Fig. 15