Pioneer Super Tuner IIID AVH-P4000DVD Посібник з монтажу

Переглянути онлайн або завантажити pdf Посібник з монтажу для Автомобільний приймач Pioneer Super Tuner IIID AVH-P4000DVD. Pioneer Super Tuner IIID AVH-P4000DVD 8 сторінок. Pioneer avh-p4000dvd: install guide
Також для Pioneer Super Tuner IIID AVH-P4000DVD: Посібник з монтажу (6 сторінок)

Друкувати сторінку

AVH-P4000DVD

Printed in Thailand

Напечатано в Таиланде

<CRD4280-A/N> RE

Connecting the units

WARNING

Note

• To avoid the risk of accident and the potential

• This unit cannot be installed in a vehicle without

violation of applicable laws, the front DVD or TV

ACC (accessory) position on the ignition switch.

(sold separately) feature should never be used

while the vehicle is being driven. Also, Rear

Displays should not be in a location where it is a

visible distraction to the driver.

• In some countries or states the viewing of images

on a display inside a vehicle even by persons

other than the driver may be illegal. Where such

regulations apply, they must be obeyed and this

unit's DVD features should not be used.

ACC position

No ACC position

CAUTION

• Use this unit in other than the following

• PIONEER does not recommend that you

conditions could result in fire or malfunction.

install or service your display yourself.

— Vehicles with a 12-volt battery and negative

Installing or servicing the product may

grounding.

expose you to risk of electric shock or other

— Speakers with 50 W (output value) and 4 ohm

hazards. Refer all installation and servicing

to 8 ohm (impedance value).

of your display to authorized Pioneer service

• To prevent short-circuit, overheating or

personnel.

malfunction, be sure to follow the directions

• Secure all wiring with cable clamps or

below.

electrical tape. Do not allow any bare wiring

— Disconnect the negative terminal of the

to remain exposed.

battery before installation.

• Do not drill a hole into the engine

— Secure the wiring with cable clamps or

compartment to connect the yellow lead

adhesive tape. To protect the wiring, wrap

of the unit to the vehicle battery. Engine

adhesive tape around them where they lie

vibration may eventually cause the insulation

against metal parts.

to fail at the point where the wire passes from

— Place all cables away from moving parts, such

the passenger compartment into the engine

as gear shift and seat rails.

compartment. Take extra care in securing the

— Place all cables away from hot places, such as

wire at this point.

near the heater outlet.

• It is extremely dangerous to allow the display

— Do not pass the yellow cable through a hole

lead to become wound around the steering

into the engine compartment to connect to a

column or gearshift. Be sure to install the

battery.

display in such a way that it will not obstruct

— Cover any disconnected cable connectors with

driving.

insulating tape.

• Make sure that wires will not interfere with

— Do not shorten any cables.

moving parts of the vehicle, such as the

— Never cut the insulation of the power cable of

gearshift, parking brake or seat sliding

this unit in order to share the power to other

mechanism.

equipment. Current capacity of the cable is

• Do not shorten any leads. If you do, the

limited.

protection circuit may fail to work properly.

— Use a fuse of the rating prescribed.

— Never wire the speaker negative cable directly

to ground.

WARNING

— Never band together multiple speaker's

negative cables.

LIGHT GREEN LEAD AT POWER CONNECTOR

IS DESIGNED TO DETECT PARKED STATUS

AND MUST BE CONNECTED TO THE POWER

SUPPLY SIDE OF THE PARKING BRAKE SWITCH.

IMPROPER CONNECTION OR USE OF THIS

LEAD MAY VIOLATE APPLICABLE LAW AND MAY

RESULT IN SERIOUS INJURY OR DAMAGE.

Connecting the units

• Control signal is output through blue/white cable

when this unit is powered on. Connect it to an

external power amp's system remote control or

the vehicle's auto-antenna relay control terminal

(max. 300 mA, 12 V DC). If the vehicle is equipped

with a glass antenna, connect it to the antenna

booster power supply terminal.

• Never connect blue/white cable to external power

amp's power terminal. Also, never connect

it to the power terminal of the auto antenna.

Otherwise, battery drain or malfunction may

result.

• IP-BUS connectors are color-coded. Be sure to

connect connectors of the same color.

• Black cable is ground. This cable and other

product's ground cable (especially, high-current

products such as power amp) must be wired

separately. Otherwise, fire or malfunction may

result if they are accidentally detached.

Connecting the units

Parts supplied

Parts marked (*) are pre-installed.

This product

Power cord

USB cable

Holder*

Side bracket (2 pcs.)*

Trim ring

Frame

Flush surface screw

Binding screw

(5 × 6 mm) (8 pcs.)

(4 pcs. are pre-installed.)

Binding screw*

Rubber bush

Double-ended screw

(3 × 6 mm) (8 pcs.)

Touch panel pen