Pioneer X-HMD03 Інструкція з експлуатації - Сторінка 22
Переглянути онлайн або завантажити pdf Інструкція з експлуатації для Автомобільний приймач Pioneer X-HMD03. Pioneer X-HMD03 36 сторінок. Cd/receiver system
Друкувати сторінку
Listening to the Radio
Auto station search
The auto station search function automatically
searches for radio stations that have good
reception.
Press and hold the + or – button.
Release the button once the frequency shown
in the display panel starts changing. The auto
search function will automatically stop at the
next station that has good reception.
Notes concerning auto station search
• The auto search function may not operate correctly
from 90 MHz to 108 MHz in the FM band, due to
interference from TV signals. In such cases, use the
manual station selection method.
• When TV reception shares some bandwidth with FM
reception,it may interfere with the FM signals.
Tuning interval
The two factory settings for the AM tuning
interval are 10 kHz per step (in U.S. and Cana-
dian models) and 9 kHz per step (in Taiwanese
and European models).
The two factory settings for the FM tuning
interval are 100 kHz per step (in U.S. and
Canadian models) and 50 kHz per step (in
Taiwanese and European models).
When using the CD/Receiver System in a region
that has a different AM/FM frequency band
allocation, perform the following operation to
change the AM/FM tuning interval from 10 kHz/
100 kHz per step to 9 kHz/50 kHz per step (or
vice-versa).
While tuned to an AM or FM station, press and
hold the STOP button first, then press and hold
the MODE button. Keep all two buttons
pressed for at least three seconds.
The AM/FM tuning range is switched as shown
in Table below.
Model
Default settings
Taiwanese
AM: 531 to 1,602
and
kHz in 9-kHz
European
step
models
FM: 87.50 to 108.00
MHz in 50-kHz
step
U.S. and
AM: 530 to 1,700
Canadian
kHz in 10-kHz
models
step
FM: 88.0 to 108.0
MHz in 100-kHz
step
Switched to
AMW: 530 to 1,600
kHz in 10-kHz
step
FMW: 88.0 to 108.0
MHz in
100-kHz
AMW: 531 to 1,602
kHz in 9-kHz
step
FMW: 87.50 to
108.00 MHz
in 50-kHz step
Presetting radio stations
Preset your favorite radio stations in the CD/
receiver's memory. Up to 12 FM and 12 AM
stations can be stored in memory.
1
Tune the radio to the station to be
preset.
2
Press and hold the ENTER button for at
least three seconds.
Make sure "PGM" appears in the display
panel, which indicates that the radio station
you were tuned to at Step 1 has been stored
in memory.
Memory registration number of radio
station
To preset another station
When you press and hold the ENTER button to preset a
radio station, the tuner is set to preset station select
mode (see the next page). To preset another radio
station, perform the following steps.
1
Press and hold the + or – button to select a station
using the auto station search function.
2
Press and hold the ENTER button for at least three
seconds.
To cancel Preset Station Select mode, press the MODE
button repeatedly until "PGM" no longer appears in the
display panel.
If 12 stations have already been preset
If "FULL" appears in the display panel when you try to
preset another radio station, it means there is no more
room in memory for additional preset stations. You must
clear at least one of the previously preset radio stations
before any additional stations can be preset.
See the next page for instructions on clearing preset
radio stations.
Radio stations must be preset again in the
following situations:
• If the power plug is disconnected from the wall
socket
• If a power outage occurs
PGM