Pioneer DMH-C5500NEX Посібник з монтажу - Сторінка 3

Переглянути онлайн або завантажити pdf Посібник з монтажу для Приймач Pioneer DMH-C5500NEX. Pioneer DMH-C5500NEX 29 сторінок. Rds av receiver

Друкувати сторінку

(Maximum input power) and between 4

Ω to 8 Ω (impedance value). Do not use 1

Ω to 3 Ω speakers for this unit.

• When rear speaker output is used by 2 Ω

of subwoofer, use speakers over 70 W

(Maximum input power).

*Please refer to connection for a

connection method.

• The black cable is ground. When

installing this unit or power amp (sold

separately), make sure to connect the

ground wire first. Ensure that the ground

wire is properly connected to metal parts

of the car's body. The ground wire of the

power amp and the one of this unit or

any other device must be connected to

the car separately with different screws. If

the screw for the ground wire loosens or

falls out, it could result in fire generation

of smoke or malfunction.

Ground wire

POWER AMP

Other devices

Metal parts of car's

(Another electronic

body

device in the car)

*1 Non supplied for this unit

• When replacing the fuse, be sure to only

use a fuse of the rating prescribed on this

product.

• This product cannot be installed in a

vehicle without ACC (accessory) position

on the ignition switch.

ACC position

No ACC position

• To avoid short-circuiting, cover the

disconnected lead with insulating tape. It

is especially important to insulate all

unused speaker leads, which if left

uncovered may cause a short circuit.

• For connecting a power amp or other

devices to this product, refer to the

manual for the product to be connected.

• The graphical symbol

placed on

the product means direct current.

Notice for the blue/

white lead

• When the ignition switch is turned on

(ACC ON), a control signal is output

through the blue/white lead. Connect to

an external power amp's system remote

control terminal, the auto-antenna relay

control terminal, or the antenna booster

power control terminal (max. 300 mA 12

V DC). The control signal is output

through the blue/white lead, even if the

audio source is switched off.

This product

Microphone 3 m (9 ft. 10-1/8 in.)

Wired remote input

Hard-wired remote control adapter can

be connected (sold separately).

iDatalink adapter (sold separately) input

(DMH-C5500NEX/DMH-C2550NEX)

This product

Antenna jack

Front output (STD)/High range output

(NW)

Rear output (STD)/Middle range output

(NW)

Subwoofer output (STD)/Low range

output (NW)

Power supply

Fuse (10 A)

SiriusXM Connect Vehicle Tuner

Refer to the instruction manual for

SiriusXM Connect Vehicle Tuner (sold

separately).

Monitor cable connector

Connect to LCD screen

NOTE

Before using and/or connecting the

iDatalink Maestro adapter (sold

separately), you will need to first flash the

Maestro module with the appropriate

vehicle and head unit firmware. You can

find the device number that is required for

the activation on the followings (refer to

the Operation Manual.):

• The label on the packaging of this

product

• The label on this product

• The [Firmware Information] screen

Power cord

To power supply

Power cord

Yellow

To terminal supplied with power

regardless of ignition switch position.

Red

To electric terminal controlled by

ignition switch (12 V DC) ON/OFF

Orange/white

To lighting switch terminal.

Black (ground)

To vehicle (metal) body.

Violet/white

Of the two lead wires connected to the

back lamp, connect the one in which

the voltage changes when the gear shift

is in the REVERSE (R) position. This

connection enables the unit to sense