Pioneer VSX-D3S Інструкція з експлуатації - Сторінка 9
Переглянути онлайн або завантажити pdf Інструкція з експлуатації для Стерео приймач Pioneer VSX-D3S. Pioneer VSX-D3S 40 сторінок. Audio/video stereo receiver
Також для Pioneer VSX-D3S: Інструкція з експлуатації Посібник з експлуатації (40 сторінок)
Друкувати сторінку
SPEAKER SYSTEM CONNECTIONS
NOTE:
Use speakers with an impedance of 8
When connecting speakers to the FRONT SPEAKERS B terminals,
the procedure is the same as that used for connecting speakers
to the FRONT SPEAKERS A terminals.
NOTE:
÷ Do not allow any of the cord's conductors to protrude from the
terminals or touch any other conductors. Malfunctioning or
breakdowns may occur when conductors come into contact
with each other.
÷ If you have one pair of speakers only, connect it to front
speaker terminals A or B.
÷ Be sure to connect single rear speaker to the L channel.
I+II
SPEAKER
SELECTOR
I ONLY
SUB WOOFER
CENTER
PRE
PRE
OUT
OUT
I+II
CENTER
+
SPEAKERS
I ONLY
–
SEE
I
II
INSTRUCTION
MANUAL
+
R
–
R
L
REAR
SPEAKERS
R
–
+
–
CENTER
+
–
SP-A(L)
(L)
+
–
NOTE:
Before connecting pin jacks, speaker cables and other jacks and cables, switch power to the unit
OFF, and wait for about one hour. (When power is ON, the rear panel may become very hot.)
to 16
.
TWO VOLTAGE SELECTORS
SPEAKER
SELECTOR
110V
SPEAKER
120 127V
IMPEDANCE
8
16
SPEAKER
CAUTION:
THE POWER
220V
240V
SUPPLY CORD SHOULD
220V
BE DISCONNECTED
110V
120-127V
240V
BEFORE CHANGING
THE VOLTAGE
SELECTOR.
+
A
L
SWITCHED
–
TOTAL 100W MAX
FRONT
SPEAKERS
UNSWITCHED
100W MAX
L
B
CAUTION:
SPEAKER IMPEDANCE
DO NOT CONNECT
8
16
SPEAKER
TV SET CR MONITOR.
AC OUTLETS
Illustration
+
shows Multi-
voltage model.
FRONT
+
–
+
–
SP-A(R)
(R)
+
–
REAR
You can set this unit to match the requirements and
specifications of your stereo system's speakers (whether or
not center speaker(s), rear speakers or a sub-woofer are
used, speaker size, etc.) to assure optimum sound quality.
Before using, perform settings in the SPEAKER MODE (refer
to page 29).
NOTE:
This unit does not feature conventional switching between
NORMAL / WIDE / PHANTOM center modes.
Speaker cord connection
2
1
1 Push the lever forward.
2 Insert the cord into the hole.
3 Pull the lever back.
Connecting Two Center Speakers for Dual Center
There are two sets of terminals for center speakers on the main
unit, so you can connect two speakers. When you cannot install
a speaker under or behind your TV, installing speakers either
side of the TV as a center speaker is just as effective.
When the SPEAKER SELECTOR switch is in the " + " position,
be sure to connect two speakers. If only one speaker is connected,
there will be no sound.
Both speaker systems should have an impedance of 4
+
–
+
2
3
1
TWO VOLTAGE SELECTORS
CENTER
SUB WOOFER
SPEAKER
SELECTOR
PRE
PRE
110V
OUT
OUT
SPEAKER
120 127V
I+II
IMPEDANCE
8
16
CENTER
SPEAKER
SPEAKERS
CAUTION:
THE POWER
240V
220V
I ONLY
SUPPLY CORD SHOULD
220V
BE DISCONNECTED
120-127V
110V
240V
BEFORE CHANGING
THE VOLTAGE
SELECTOR.
SEE
A
I
II
INSTRUCTION
MANUAL
R
L
SWITCHED
TOTAL 100W MAX
FRONT
SPEAKERS
UNSWITCHED
R
L
REAR
100W MAX
SPEAKERS
R
L
B
CAUTION:
SPEAKER IMPEDANCE
DO NOT CONNECT
8
16
SPEAKER
TV SET CR MONITOR.
AC OUTLETS
–
+
Illustration shows
Multi-voltage model.
–
+
CONNECTIONS
3
1 Loosen cap.
2 Insert wire.
3 Tighten cap.
to 16 .
SPEAKER
SELECTOR
I+II
I ONLY
–
+
9
<
>
ARB7050