Pioneer VSX-D510 Інструкція з експлуатації Посібник з експлуатації - Сторінка 21
Переглянути онлайн або завантажити pdf Інструкція з експлуатації Посібник з експлуатації для Стерео приймач Pioneer VSX-D510. Pioneer VSX-D510 40 сторінок. Audio/video multi-channel receiver
Також для Pioneer VSX-D510: Інструкція з експлуатації Посібник з експлуатації (36 сторінок), Посібник з експлуатації (14 сторінок)
Друкувати сторінку
Switching ANALOG/DIGITAL
Signal Input
When you select a function (for example CD) that is
only hooked up by a digital connection, then the
ANALOG/DIGITAL signal input switch will
automatically choose digital. If you have that function
hooked up by both digital and analog connections this
switch lets you choose which to listen to.
MULTI CONTROL
DVD/LD TV/SAT VCR/DVR
1
RECEIVER TUNER
2
DSP MODE MIDNIGHT 5.1CH
1
2
CHANNEL
TEST
SELECT
TONE
5
6
CHANNEL
LEVEL
9
0
FUNC
1 Press
.
RECEIVER
This switches the remote to the surround setup
mode.
2 Press
SIGNAL SELECT
signal corresponding to the source
component.
Each press switches between ANALOG and DIGITAL
signal selection.
3 While
SIGNAL SELECT
2 DIGITAL lights when a Dolby Digital
signal is input, DTS lights when a DTS signal
is input.
MEMO:
• SIGNAL SELECT is fixed in the "ANALOG" position
for components not assigned to one of the two digital
input jacks.
• This receiver can only play back Dolby Digital, PCM
(32kHz, 44kHz, and 48kHz), DTS, digital signal
formats. With digital signal formats other than these,
set SIGNAL SELECT to "ANALOG".
• When a LD or CD player compatible with DTS is
played back with SIGNAL SELECT set in "ANALOG",
digital noise may be output by playing back the DTS
directly (no decoding). To prevent noise, you need to
make digital connections (Refer to page 6) and set
SIGNAL SELECT to "DIGITAL".
• Some DVD players don't output DTS signals. For
more details, refer to the instruction manual supplied
with your DVD player.
Î
CD
CD-R/
TV CONT
TAPE/MD
3
4
2
SIGNAL
ATT
SELECT
7
8
EFFECT
10
DISC
CH
to select the input
is set to DIGITAL,
Playing Sources with Dolby
Digital or DTS Sound
MULTI CONTROL
DVD/LD TV/SAT VCR/DVR
RECEIVER TUNER
4
2
DSP MODE MIDNIGHT 5.1CH
1
2
CHANNEL
TEST
SELECT
TONE
6
5
6
CHANNEL
LEVEL
9
0
2
FUNC
TV CONTROL
VOL
ST
ENTER
MENU
SOURCE CLASS
3
D.ACCESS
LOUDNESS FUNCTION MUTING
FL
2
RECEIVER
DIMMER
1 Turn on the power of the playback
component.
2 Turn on the power of the receiver.
Be sure that the standby indicator turns off on the
front panel.
3 Press a
MULTI CONTROL
the source you want to playback.
If the DIRECT FUNCTION is OFF you have to use
the
button to select the source (see p.
FUNCTION
32).
4 Press
.
RECEIVER
Then set the remote to select the sound mode.
5 Press
SIGNAL SELECT
(Refer to "Switching ANALOG/DIGITAL signal input"
on this page.)
6 Press 2 to switch the Dolby/DTS mode on.
7 Start playback of the component you
selected in step 1.
8 Press
MASTER VOLUME (+/–)
volume level.
Sound Modes
CD
3
CD-R/
TV CONT
TAPE/MD
3
4
SIGNAL
5
ATT
SELECT
7
8
EFFECT
10
DISC
CH
VOL
FQ
ST
TOP
MENU
FQ
MPX
BAND
CHANNEL
DISPLAY RF ATT
8
REMOTE
MASTER
SETUP
VOLUME
button to select
to select DIGITAL.
to adjust the
21
En