Pioneer A-88X Інструкція з експлуатації Посібник з експлуатації - Сторінка 5
Переглянути онлайн або завантажити pdf Інструкція з експлуатації Посібник з експлуатації для Підсилювач Pioneer A-88X. Pioneer A-88X 13 сторінок.
Також для Pioneer A-88X: Посібник з експлуатації (23 сторінок), Інструкція з експлуатації Посібник з експлуатації (13 сторінок), Інструкція з експлуатації Посібник з експлуатації (12 сторінок)
Друкувати сторінку
FRONT PANEL
LINE
STRAIGHT
:
an
MM
STRAIGHT
¢
TAPE
COPY
Tm
2OFF
Om
SPEAKERS
MODE
*
STEREO
q
OFF
MONO
8
REV
he
ae
(|
\Y
\
aa
PHONES
[~~]
©
@) POWER switch/indicator
Press to turn power to the unit ON and OFF.
Depressed position (ON): Power is supplied to the unit.
Released position (OFF): Power to the unit is disconnected.
@) SPEAKERS selector switch
Use to select the speaker systems used for playback.
[OFF]
.
— No sound is produced from the speaker systems. Set to
this position when using headphones.
[A]
— Sound is produced from the speaker systems connected
to the SPEAKERS A terminals.
[B]
— Sound is produced from the speaker systems connected
to the SPEAKERS B terminals.
[A+B]
— Sound is produced from both the speaker systems con-
nected to the SPEAKERS
A and SPEAKERS B terminals.
@) MODE selector switch
Use to select the playback mode.
[STEREO]
— Set here for normal stereo reproduction.
The left-channel sound (signals connected to the rear panel
L terminals) will be produced from the left-side speaker
systems,
and right-channel sound
(signals connected to
the rear panel R terminals) will be produced from the right-
side speaker systems.
[REV]
— When set to this position, the stereo channels will be
reversed, the left-channel sound being produced from the
right side speaker systems, and the right-channel sound
being produced from the left-side speaker systems.
[MONO]
— The left-channel and right-channel signals will be mixed
and produced from the right and left side speaker systems
simultaneously.
This function does not operate when the LINE STRAIGHT
switch is in the ON position.
WRPIONEER
STEREO
4MPLFIER
A-38x
PANEL FACILITIES
PHONO
$E6LECTOR
MC
TRA
FORMER
TAPE
MONITOR
TAPE
1 OFF
TAPES
i
QD
@) BASS tone control
Use to adjust the low-frequency tones. The central ''0'' posi-
tion is the flat (normal) position. When turned to the right,
low-frequency tones are emphasized;
when turned to the
left, low-frequency tones are de-emphasized.
This function does not operate when the LINE STRAIGHT
switch is in the ON position.
G) TREBLE tone control
Use for adjusting the high-frequency tones.
The central "'0'' position is the flat (normal) position. When
turned to the right, high-frequency tones are emphasized;
when
turned
to
the
left,
high-frequency
tones
are
de-
emphasized.
This function does not operate when the LINE STRAIGHT
switch is in the ON position.
@) LINE STRAIGHT switch/indicator
By using this switch, the input signals from the various con-
nected peripheral components can be played back through
the amplifier's modifying (tone, mode) circuits, or bypassing
those circuits.
When
the indicator is lighted, the function
is ON.
Input
signals will bypass the modifying circuits and be played back
with pure, flat-balanced tone.
When set to OFF, input signals will pass through the modify-
ing circuits before being played back, thus allowing you to
adjust bass and treble tone, and select the mode of playback
with the MODE selector switch.
@ PHONO SELECTOR switch
Set in accordance with the type of cartridge used in your
turntable.
[MC TRANSFORMER]
— When using an MC (moving coil) cartridge, set either to
the [3 92] or [40 2] position. The 3 ohm and 40 ohm selec-
tion should be made on the basis of the cartridge's load
resistance (impedance) value.