Pioneer VSA-1000 Інструкція з експлуатації Посібник з експлуатації - Сторінка 31
Переглянути онлайн або завантажити pdf Інструкція з експлуатації Посібник з експлуатації для Підсилювач Pioneer VSA-1000. Pioneer VSA-1000 35 сторінок. Av digital surround amplifier
Також для Pioneer VSA-1000: Інструкція з експлуатації Посібник з експлуатації (35 сторінок)
Друкувати сторінку
TROUBLESHOOTING
to carry out repair work.
Sound from only one speaker.
Recording on tape is impossible.
Copying of tapes is impossible.
Problem
Probable cause
Remedy
No power.
* The power plug is not inserted in the wall socket. | * Plug into the wall socket.
* It is plugged into the power outlet of another
© Turn on the power to other appliances.
appliance which is switched off.
No sound.
© The MUTING {— 09) switch is on.
© Switch the MUTING (— 0) off.
* The connecting cord plugs are incorrectly
¢ Check the connections.
attached to the jacks or connected to the wrong
jacks.
* The jacks or plugs are dirty.
* Clean the jacks and plugs.
* SPEAKER switches are turned OFF.
* Press the SPEAKER switch to turn ON.
* The connector bars of the PRE OUT jacks or
* Connect the connector bars, (Refer to page 16)
POWER AMP IN jacks are disconnected.
In cases other
* The TAPE 2/DAT 2 MONITOR is ON.
* Set the switch to OFF.
than Tape 2.
© The input selector switch setting is not
* Change the switch correctly.
appropriate for the source selected.
© There is a mistake in the operation of another
© Refer to the instruction manuals of other
component.
components being employed.
In the case
* The TAPE 2/DAT 2 MONITOR is set to OFF.
* Set the switch to ON.
of Tape 2.
* Incorrect operation of the tape deck.
© Refer to the tape deck instruction manual.
No picture.
* The connecting cord is not firmly plugged in to
© Check the connections,
the jacks, or it is attached to the wrong jacks.
* The jacks or plugs are dirty.
* The input selector switch is in the wrong position.
* The VIDEO ADAPTOR switch is ON.
* Other components are not being operated
correctly.
© The connecting cord or speaker cord is loose.
* The balance adjustment is incorrect.
* Incorrect operation of the cassette deck,
* Clean the jacks and plugs.
* Change the switch correctly.
* Set the switch to OFF.
* Refer to the instruction manuals of other
components being employed.
© Check the connections.
* Press the left and right balance switches at the
same time to reach the center position.
* Refer to the cassette deck instruction manual.
* Incorrect operation of the cassette deck.
* Refer to the cassette deck instruction manual.
There is no surround sound.
¢ The surround switch is OFF.
* The input sound is mono but the mode is
STUDIO, STADIUM or DOLBY PRO LOGIC
SURROUND.
* The front and rear speakers are connected in
reverse.
* The input selector switch is not appropriate for
the component playing.
* Select the surround mode with the SURROUND
MODE switch.
* Switch ON the SIMULATED SURROUND.
* Check that the connections are correct.
* Change the switch correctly,
The remote control unit does
not work.
* Batteries dead or no batteries in remote control
unit.
* Poor angle or too great a distance from the
remote sensor window.
* There is an obstacle between you and the
remote sensor window.
* Insert battery. Or change to new battery.
* Use within seven meters and within a 30 degrees
angle left or right of the remote sensor window.
* Change your position or move the obstacle.
Optional components can't be
controlled by the remote
control unit.
* The control cord is not connected.
* Connect securely. (Refer to page 17}
31
<ARB1177>