Pioneer Super Tuner IIID DEH-P5800MP Посібник з експлуатації - Сторінка 28
Переглянути онлайн або завантажити pdf Посібник з експлуатації для Програвач компакт-дисків Pioneer Super Tuner IIID DEH-P5800MP. Pioneer Super Tuner IIID DEH-P5800MP 38 сторінок. Owner's manual
Також для Pioneer Super Tuner IIID DEH-P5800MP: Посібник з монтажу (6 сторінок), Посібник користувача (34 сторінок)
Друкувати сторінку
Audio Adjustments
Adjusting loudness
Loudness compensates for deficiencies in the low- and high-sound ranges at low
volume.
1. Press AUDIO to select LOUD.
Press AUDIO until LOUD appears in the display.
2. Press 8 to turn loudness on.
Loudness level (e.g., LOUD :MID) appears in the display.
3. Press 4 or 6 to select a desired level.
Each press of 4 or 6 selects level in the following order:
LOW (low) – MID (mid) – HI (high)
4. Press 2 to turn loudness off.
LOUD :OFF appears in the display.
Using subwoofer output
Turning a subwoofer on/off
This unit is equipped with a subwoofer output which can be turned on or off.
1. Press AUDIO to select SUB, W.
Press AUDIO until SUB, W appears in the display.
• You can also select the subwoofer setting menu by pressing SW on the unit.
• When the subwoofer controller setting is P/O:FUL, you cannot select SUB, W.
2. Press 8 to turn subwoofer output on.
Sub W.:NOR appears in the display. Subwoofer output is now on.
• If the subwoofer output phase has been set to the reverse, Sub W.:REV will be
displayed.
• To turn subwoofer output off, press 2.
3. Press 4 or 6 to select the phase of subwoofer output.
Press 4 to select reverse phase and Rev. appears in the display. Press 6 to select
normal phase and Normal appears in the display.
Adjusting subwoofer settings
When the subwoofer output is on, you can adjust the cut-off frequency and the output
level of the subwoofer.
1. Press AUDIO to select 80: 0.
Press AUDIO until 80: 0 appears in the display.
• When the subwoofer output is on, you can select 80: 0.
• If the subwoofer setting has been previously adjusted, the frequency of that
previously selected will be displayed instead of 80.
• You can also select the subwoofer setting menu by pressing SW on the unit.
2. Press 4 or 6 to select cut-off frequency.
Each press of 4 or 6 selects cut-off frequencies in the following order:
50 – 80 – 125 (Hz)
Only frequencies lower than those in the selected range are outputted from the
subwoofer.
3. Press 8 or 2 to adjust the output level of the subwoofer.
Each press of 8 or 2 increases or decreases the level of the subwoofer. +6 – –6 is
displayed as the level is increased or decreased.
Using nonfading output
When the nonfading output setting is on, the audio signal does not pass through this
unit's low pass filter (for the subwoofer), but is outputted through the RCA output.
1. Press AUDIO to select nonfading output on/off setting.
Press AUDIO until NOFAD:ON appears in the display.
• When the subwoofer controller setting is only P/O:FUL, you can switch to the
nonfading output on/off setting. (Refer to page 31.)
2. Press 8 to turn nonfading output on.
NOFAD:ON appears in the display. Nonfading output is now on.
• To turn nonfading output off, press 2.
28