Pioneer AVH-P4900DVD - DVD Player With LCD Monitor Посібник з монтажу

Переглянути онлайн або завантажити pdf Посібник з монтажу для DVD-плеєр Pioneer AVH-P4900DVD - DVD Player With LCD Monitor. Pioneer AVH-P4900DVD - DVD Player With LCD Monitor 9 сторінок. Av receiver/dvd player
Також для Pioneer AVH-P4900DVD - DVD Player With LCD Monitor: Посібник з експлуатації (9 сторінок)

Pioneer AVH-P4900DVD - DVD Player With LCD Monitor Посібник з монтажу
AVH-P4900DVD
This product conforms to CEMA cord colors.
Le code de couleur des câbles utilisé pour ce produit est
conforme à CEMA.
Printed in Japan
Imprimé au Japon
<CRD4195-A> UC
<KSNNF> <07B00000>
Connecting the Units
WARNING
CAUTION:
• To avoid the risk of accident and the
• PIONEER does not recommend that you
potential violation of applicable laws,
install or service your display yourself.
the front DVD or TV (sold separate-
Installing or servicing the product may
ly) feature should never be used
expose you to risk of electric shock or
while the vehicle is being driven.
other hazards. Refer all installation and
Also, Rear Displays should not be in
servicing of your display to authorized
a location where it is a visible distrac-
Pioneer service personnel.
tion to the driver.
• Secure all wiring with cable clamps or
• In some countries or states the view-
electrical tape. Do not allow any bare
ing of images on a display inside a
wiring to remain exposed.
vehicle even by persons other than
the driver may be illegal. Where such
• Do not drill a hole into the engine com-
regulations apply, they must be
partment to connect the yellow lead of
obeyed and this unit's DVD features
the unit to the vehicle battery. Engine
should not be used.
vibration may eventually cause the insu-
lation to fail at the point where the wire
passes from the passenger compartment
into the engine compartment. Take extra
care in securing the wire at this point.
• It is extremely dangerous to allow the
display lead to become wound around
the steering column or gearshift. Be sure
to install the display in such a way that it
will not obstruct driving.
• Make sure that wires will not interfere
with moving parts of the vehicle, such as
the gearshift, parking brake or seat slid-
ing mechanism.
• Do not shorten any leads. If you do, the
protection circuit may fail to work prop-
erly.
ENGLISH
Note:
Control signal is output through blue/white cable
This unit cannot be installed in a vehicle that
when this unit is powered on. Connect it to an
does not have an ACC (accessory) position on
external power amp's system remote control or
the ignition switch. (Fig. 1)
the vehicle's auto-antenna relay control terminal
(max. 300 mA, 12 V DC). If the vehicle is
equipped with a glass antenna, connect it to the
antenna booster power supply terminal.
Never connect blue/white cable to external power
amp's power terminal. Also, never connect it to
the power terminal of the auto antenna.
Otherwise, battery drain or malfunction may
result.
IP-BUS connectors are color-coded. Be sure to
ACC position
No ACC position
connect connectors of the same color.
Fig. 1
Black cable is ground. This cable and other prod-
uct's ground cable (especially, high-current prod-
ucts such as power amp) must be wired separate-
Use this unit in other than the following condi-
ly. Otherwise, fire or malfunction may result if
tions could result in fire or malfunction.
they are accidentally detached.
— Vehicles with a 12-volt battery and negative
grounding.
Cord function may differ according to the
— Speakers with 50 W (output value) and 4 ohm
product, even if cord color is the same. When
to 8 ohm (impedance value).
connecting this system, be sure to check all
To prevent short-circuit, overheating or malfunc-
manuals and connect cords correctly.
tion, be sure to follow the directions below.
— Disconnect the negative terminal of the battery
before installation.
— Secure the wiring with cable clamps or adhe-
sive tape. To protect the wiring, wrap adhesive
tape around them where they lie against metal
parts.
— Place all cables away from moving parts, such
as gear shift and seat rails.
— Place all cables away from hot places, such as
near the heater outlet.
— Do not pass the yellow cable through a hole
into the engine compartment to connect to a
battery.
— Cover any disconnected cable connectors with
insulating tape.
— Do not remove RCA caps if RCA cables are
not used.
— Do not shorten any cables.
— Never cut the insulation of the power cable of
this unit in order to share the power to other
equipment. Current capacity of the cable is
limited.
— Use a fuse of the rating prescribed.
— Never wire the speaker negative cable directly
to ground.
— Never band together multiple speaker's nega-
tive cables.