Pioneer DV-505 Посібник з експлуатації - Сторінка 19
Переглянути онлайн або завантажити pdf Посібник з експлуатації для DVD-плеєр Pioneer DV-505. Pioneer DV-505 47 сторінок. Dvd/video cd/cd player code switchable modification
Також для Pioneer DV-505: Інструкція та посібник з монтажу (16 сторінок)
Друкувати сторінку
(20) Revision of the DVD mechanism controller
[M: .
/ .
]
Revision number of the external ROM part (flash ROM) of the
DVD mechanism controller
Revision of the internal ROM (core part) of the DVD mechanism
controller
(21) Revision of the CLD mechanism controller
[L: .
]
(22) Version of the AV-1 chip [AV: . ]
(23) Version of the FL controller [F: . ]
(24) Control number of the GUI-ROM [GUI:
(25) The part number of the flash ROM and system
controller [S :
Part number of the flash ROM
(Example) VYW1536-A
(Example) PD626A9
6256A9
Part number of the system controller
(Example) PD3381T1
3381T1
(26) Part number of the DVD mechanism controller
(Example) PD4889A0
4889A0
(27) Part number of the CLD mechanism controller
(Example) PD0260A2
0260A2
(28) AV1 classification [AV1 :
RAM, E/A, S/C
(29) Flash ROM size [FLSH :
8M : 8M bit, 4M : 4M bit
3.8 DESCRIPTIONS OF NEW FUNC-
TIONS IN TEST MODE
3.8.1 Error Rate
Overview
The error rate of CDs can be measured on basic models, such as the
DV-505, and that of CDs as well as LDs with sub-Q codes can be
measured on DVD/LD-compatible models, such as the DVL-909.
The value is displayed in decimal and indicates the number of C1
errors (including the corrected ones) counted during the specified
measurement time.
An indeterminate measurement result may be caused by a dirty disc,
decentering, surface deflection, birefringence (double reflection),
or a pickup problem (dirty lens, etc.), misadjustments of the pickup,
improper automatic adjustment, or incomplete adjustments. On the
manufacturing line, the value is used for yes/no decision of pickups.
Normally, for a measurement for 5 seconds, the value may be less
than 10 with a clean disc and less than 100 with a disc with some
damage.
<Front>
<Rear>
]
/
]
<Front>
W1536A
<Rear>
]
]
DV-505, DVL-909, DV-S9
Using the Function in Test Mode (The Remote
Control Keys to be Used are Indicated in Brackets)
(1) Set the CD to trace (playback) state.
(2) Set the player to Number input mode by pressing [+10] and
enter the measurement time in a range of 1 to 5 (sec.).
(3) Start measurement by pressing [TEST] + [0]. The SubQ counter
stops during measurement, but this is not a malfunction. When
the specified measurement time has elapsed, the result is
indicated to the right of "ER C1 –" on the screen.
If you skip step 2, the measurement time is set to 5 (sec).
3.8.2 Jitter Value
Overview
The jitter values of DVDs and CDs can be displayed on basic models,
such as the DV-505, and those of DVDs can be displayed on DVD/
LD-compatible models, such as the DVL-909.
The displayed value shows a voltage in three-digit decimal as .
For example, the indication "0278" means 2.78 V. The larger the
value, the worse the jitter. The worst value is 3.25 V. When playing
a DVD or a video CD with which the jitter value is extremely high,
mosaics may be seen. As with the error rate, the jitter depends on
the disc and pickup. The jitter value to be displayed has no close
correlation with a jitter measuring device, and is to be regarded just
for reference.
Reference : When the jitter value is 2.9 V or more with a DVD, or
3.0 V or more with a CD (or a video CD), it may cause
a problem (mosaic, audio distortion, etc.) in playback.
Using the Function in Test Mode (The Remote
Control Keys to be Used are Indicated in Brackets)
(1) Set the DVD or CD to trace (playback) state with AGC OFF.
(2) Press [TEST] and [DIGITAL/ANALOG].
The current jitter value appears to the right of "JT:
the display. The jitter value keeps changing unless any additional
key operation is made.
Note : Although a value may be displayed on the screen even with
AGC ON, this is NOT a jitter value.
The jitter value with AFB ON cannot be displayed (see the
next section). The jitter value with AFB ON can be obtained
only by directly measuring the voltage at the JV connector
(pin 94) of the servo DSP (LC78650).
V.
" on
19