Pioneer PDP-S01-LR Інструкція з експлуатації Посібник з експлуатації - Сторінка 5

Переглянути онлайн або завантажити pdf Інструкція з експлуатації Посібник з експлуатації для Акустична система Pioneer PDP-S01-LR. Pioneer PDP-S01-LR 17 сторінок.

Друкувати сторінку

Pioneer PDP-S01-LR Інструкція з експлуатації Посібник з експлуатації

[2] Installation using commercial

mounting fittings

This unit includes M8 (ø 25)

washers for installation on

commercial mounting fittings.

Installation is made by two-point

fixing at one of the mounting

holes for commercial mounting

fittings. As these two mounting

holes are not at the same level,

washers are used to compensate

for this difference.

Washer M8

(ø 25)

CONNECTION TO A STEREO

AMPLIFIER

1. Switch off the power of the amplifier.

2. Connect the input terminals of the speaker system and

the speaker output terminals of the stereo amplifier with

the accessory speaker cable. The polarity of the input

terminals is plus

for the red terminal (the terminal on

the right side in the following figure) and minus

black terminal (the terminal on the left side in the

following figure).

1 Remove the insulation

and twist the core ends

together.

terminal

(Speaker output terminals

of the stereo amplifier)

After connection to the terminals, pull lightly on the cable

to confirm that the tips of the cable are connected

positively to the terminals. An imperfect connection can

cause sound interruptions and noise.

When cable cores stick out and

circuited, an excessive load will be applied to the stereo

amplifier and the operation will stop or trouble will be

caused.

When the polarity is reversed for one speaker (left or

right) at the time of connection to the stereo amplifier,

the bass reproduction will be reduced, the sound

positioning will be lost, and a correct stereo effect will

not be obtained.

Two-point fixing at either position.

For compensation of the level

difference between the two holes,

a washer is used at the lower

monting hole.

for the

2 Push the lever, insert the

cable into the hole, and

release the lever.

terminal

To the

terminal To the

terminal

and

lines are short-

CABINET MAINTENANCE

Use a polishing cloth or dry cloth to wipe off dust and

dirt.

When the cabinet is very dirty, wipe with a soft cloth

moistened with water-diluted cleanser; then wipe again

with a dry cloth. Do not use furniture wax or cleaners.

They may damage the surface of the cabinet.

Never use thinner, benzine, insecticide sprays and other

chemicals on or near the cabinets, since these will

corrode the surfaces.

When a chemical cloth is used, read the cautions for the

chemical cloth carefully.

SPECIFICATIONS

Cabinet :

Enclosed type with stagger circuit, antimagnetic design

Used speakers (three-way method) :

Woofer (for low tones) ........................... Oval cone type

Mid-range (middle range) ....................... Oval cone type

Tweeter (for high tones) .................... 2.5 cm dome type

Nominal impedance ..................................................... 8 Ω

Frequency Range ..................................... 50 to 60,000 Hz

Sensitivity ................................ 82 dB/W (at 1 m distance)

Permissible input :

Max. input ............................................................... 12 W

Rated input .............................................................. 4 W

Crossover frequency ................................................ 4 kHz

External Dimensions ........ 74 (W) x 714 (H) x 103 (D) mm

Weight ..................................................................... 2.9 kg

Accessory parts (for 2 speakers) . ................................... ..

Speaker cable x 2, Flat countersunk head screw x 4,

Hexagon socket head screw x 4, Hex wrench x 1,

Washer M8 (ø 25) x 4, Washer (ø 15) x 4,

Mounting fittings x 4, Opareting Instructions x 1

NOTE:

Specifications and design subject to possible modfication

without notice, due to improvements.

Published by Pioneer Electronic Corporation.

English