Aeotec AEOEZW164 Посібник із швидкого старту - Сторінка 3
Переглянути онлайн або завантажити pdf Посібник із швидкого старту для Аксесуари Aeotec AEOEZW164. Aeotec AEOEZW164 10 сторінок. Indoor siren
Друкувати сторінку
29-9-2020
T
W
S
T S
Y
P
S
T
Quick trouble shooting
Here are a few hints for network installation if things dont work as expected.
1. Make sure a device is in factory reset state before including. In doubt exclude before include.
2. If inclusion still fails, check if both devices use the same frequency.
3. Remove all dead devices from associations. Otherwise you will see severe delays.
4. Never use sleeping battery devices without a central controller.
5. Dont poll FLIRS devices.
6. Make sure to have enough mains powered device to benefit from the meshing
Association - one device controls an other device
Z-Wave devices control other Z-Wave devices. The relationship between one device controlling another device is called association. In order to control a different
device, the controlling device needs to maintain a list of devices that will receive controlling commands. These lists are called association groups and they are
always related to certain events (e.g. button pressed, sensor triggers, ...). In case the event happens all devices stored in the respective association group will
receive the same wireless command wireless command, typically a 'Basic Set' Command.
Association Groups:
Group Number
1
2
3
4
5
6
7
8
9
Configuration Parameters
Z-Wave products are supposed to work out of the box after inclusion, however certain configuration can adapt the function better to user needs or unlock further
enhanced features.
IMPORTANT: Controllers may only allow configuring signed values. In order to set values in the range 128 ... 255 the value sent in the application shall be the
desired value minus 256. For example: To set a parameter to 200 it may be needed to set a value of 200 minus 256 = minus 56. In case of a two byte value the
same logic applies: Values greater than 32768 may needed to be given as negative values too.
Parameter 1: Configure the Light Effect and Tone Play Mode for Endpoint 1(Browse).
Please refer to the Product Manual for more details.
Size: 4 Byte, Default Value: 16777216
Setting
16777216 - 2147418112
Parameter 2: Configure the Light Effect and Tone Effect for Endpoint 2(Tampering).
Please refer to the Product Manual for more details.
Size: 4 Byte, Default Value: 16777217
manual.zwave.eu/backend/make.php?lang=en&sku=AEOEZW164
manual.zwave.eu/backend/make.php?lang=en&sku=AEOEZW164
R
S
Z W
S
Maximum
Description
Nodes
5
Lifeline group.
5
When Endpoint 1 starts playing tone or stops playing tone, Nodes associated are controlled and
will receive a Basic Set CC.
5
When Endpoint 2 starts playing tone or stops playing tone, Nodes associated are controlled and
will receive a Basic Set CC.
5
When Endpoint 3 starts playing tone or stops playing tone, Nodes associated are controlled and
will receive a Basic Set CC.
5
When Endpoint 4 starts playing tone or stops playing tone, Nodes associated are controlled and
will receive a Basic Set CC.
5
When Endpoint 5 starts playing tone or stops playing tone, Nodes associated are controlled and
will receive a Basic Set CC.
5
When Endpoint 6 starts playing tone or stops playing tone, Nodes associated are controlled and
will receive a Basic Set CC.
5
When Endpoint 7 starts playing tone or stops playing tone, Nodes associated are controlled and
will receive a Basic Set CC.
5
When Endpoint 8 starts playing tone or stops playing tone, Nodes associated are controlled and
will receive a Basic Set CC.
Description
Configure the Light Effect and Tone Play Mode for Endpoint 1(Browse).
P
3/10