Ariston INTESA TP30 Посібник користувача, інструкції з монтажу та обслуговування - Сторінка 8

Переглянути онлайн або завантажити pdf Посібник користувача, інструкції з монтажу та обслуговування для Котел Ariston INTESA TP30. Ariston INTESA TP30 50 сторінок.

Друкувати сторінку

INSTALLATION

6.1

Reference Standards

The technical information and instructions provided herein below

are intended for the installer / Servicing Technician so that the

unit may be installed and serviced correctly and safely.

In the United Kingdom the installation and initial start up of the

boiler must be by a CORGI Registered Installer in accordance

with the installation standards currently in effect, as well as with

any and all local health and safety standards i.e. CORGI.

In the Republic of Ireland the installation and initial start up of the

appliance must be carried out by a Competent Person in accor-

dance with the current edition of I.S.813 "Domestic Gas

Installations", the current Building Regulations, reference should

also be made to the current ETCI rules for electrical installation.

This appliance must be installed by a competent installer in

accordance with current Gas Safety (installation & use)

Regulations.

The installation of this appliance must be in accordance with the

relevant requirements of the Local Building Regulations, the cur-

rent I.E.E. Wiring Regulations, the bylaws of the local water

authority, in Scotland, in accordance with the Building Standards

(Scotland) Regulation and Health and Safety document No. 635

"Electricity at work regulations 1989" and in the Republic of

Ireland with the current edition of I.S. 813, the Local Building

Regulations (IE).

C.O.S.H.H.

Materials used in the manufacture of this appliance are non-haz-

ardous and no special precautions are required when servicing.

Installation should also comply with the following British Standard

Codes of Practice

BS 7593:1992

Treatment of water in domestic hot water

central heating systems

BS 5546:1990

Installation of hot water supplies for

domestic purposes

BS 5440-1:2000 Flues

BS 5440-2:2000 Air supply

BS 5449:1990

Forced circulation hot water systems

BS 6798:1987

Installation of gas fired hot water boilers

of rated input not exceeding 60kW

BS 6891:1989

Installation of low pressure gas pipe up to

28mm

BS 7671:2001

IEE wiring regulations

BS 4814:1990

Specification for expansion vessels

BS 5482:1994

Installation of L.P.G.

Supplied By www.heating spares.co Tel. 0161 620 6677

6.2

Siting the Appliance

The appliance may be installed in any room or indoor area,

although particular attention is drawn to the requirements of the

current I.E.E. Wiring Regulations, and in Scotland, the electrical

provisions of the Building Regulations applicable in Scotland,

with respect to the installation of the combined appliance in a

room containing a bath or shower, the location of the boiler in a

room containing a bath or shower should only be considered if

there is no alternative.

Where a room-sealed appliance is installed in a room con-

taining a bath or shower the appliance and any electrical

switch or appliance control, utilising mains electricity

should be situated so that it cannot be touched by a person

using the bath or shower, specifically in accordance with

current IEE Wiring Regulations.

The location must permit adequate space for servicing and air

circulation around the appliance as indicated in Section 6.4.

The location must permit the provision of an adequate flue and

termination.

For unusual locations special procedures may be necessary.

BS 6798-1987 gives detailed guidance on this aspect.

A compartment used to enclose the appliance must be designed

specifically for this purpose. No specific ventilation requirements

are needed for the installation within a cupboard.

This appliance is not suitable for outdoor installation.

The type C appliances (in which the combustion circuit, air

vent intake and combustion chamber are air-tight with

respect to the room in which the appliance is installed) can

be installed in any type of room.

Secondary ventilation is not required with this boiler. The boiler

must be installed on a solid, non-combustible, permanent wall to

prevent access from the rear.