Whirlpool 3358974 Інструкція з монтажу Посібник з монтажу - Сторінка 4

Переглянути онлайн або завантажити pdf Інструкція з монтажу Посібник з монтажу для Пральна машина Whirlpool 3358974. Whirlpool 3358974 6 сторінок.

Друкувати сторінку

Tilt washer backward

and

n remove wood block. Gently

lower washer to floor.

Move washer to its final location.

Remove cardboard

or hardboard

from under washer.

Tilt washer forward, raising

back legs 1 inch (2.5

centimeters)

off of floor to adjust rear self-

leveling legs. Gently lower washer to

floor. Check levelness of the washer by

placing a carpenter's

level on top of the

washer, first side to side; then front to

back.

the front legs up or down to adjust

Repeat Step 14.

When washer is level, use wrench

to turn nuts on front legs up tightly

against washer base. If nuts are

not tight against washer base, the

washer may vibrate.

Property Damage

Secure the drain hose to the tub or

standpipe with the shipping strap

removed from the back of the washer.

Failure to properly secure drain hose

could result in water damage.

n Carefullv tilt washer

Measure and mark a point approximately

15 inches (38.1 centimeters) from the plug

end of the shipping strap. Cut the

shipping strap at this point.

backwards

until front of washer is

3-4 inches (7.5-10 centimeters)

off of floor.

Insert piece of wood as brace.

Use legs and nuts from parts

n package.

Screw nut down to

within l/2 inch (1.3 centimeters)

of base.

12.

Insert legs into

correct holes at

each front corner

of washer until

nuts touch washer.

Do Not tighten nuts

until Step 15.

Check that hose is not twisted or

kinked and is securely in place.

strap

Put "hook" end of drain hose in tub or

standpipe.

Tightly wrap the shipping

strap around the drain hose and tub or

standpipe or inlet hose as shown in

Figures A-C. Push plug into the nearest

hole in the shipping strap.

If a longer drain hose is needed, drain

hose (Part No. 388423) and hose

extension kit (Part No. 285442) are

available from authorized parts

distributors. If drain hose must be

shortened, use hose kit (Part No. 285442).

Note: tf washer Is moved to adJust draln hose, the

washer must be leveled again. Repeat Steps 14-15.

Place cardboard

under the washer and carefully

move washer to avold damaglng

floor covering.

CHECK ELECTRICAL

1 n

REQUIREMENTS. BE SURE YOU

HAVE CORRECT ELECTRICAL SUPPLY AND

RECOMMENDED EARTHING METHOD.

n Check that all parts are now

installed. See parts list, Panel A. If there is

an extra part, go back through steps to

see which step was skipped.

Turn on water faucets and

n check for leaks. Tighten

couplings if there is leaking. DO NOT

OVERTIGHTEN; this could cause damage

to faucet.

Check that you have all of

W your tools. Check that the

shipping strap with 2 cotter pins and plug

was removed from the back of the washer

and used to secure the drain hose.

Untape power supply cord

n and plug into earthed outlet.

Take a few minutes and read

n the Use and Care Guide to

fully understand your new washer. Now

start the washer and allow it to complete

the regular cycle.

successfully installed

your new Whirlpool washer.

To get the most efficient use

from your new washer, read your

Whirlpool Use and Care Guide.

[ Congratulations!

)

Panel C