Whirlpool 4KWTW4605FW0 Інструкція з монтажу Посібник з монтажу - Сторінка 5
Переглянути онлайн або завантажити pdf Інструкція з монтажу Посібник з монтажу для Пральна машина Whirlpool 4KWTW4605FW0. Whirlpool 4KWTW4605FW0 11 сторінок. Top-loading washer
Також для Whirlpool 4KWTW4605FW0: Інструкція з використання та догляду (16 сторінок)
Друкувати сторінку
Drain System
Drain system can be installed using a floor drain, wall standpipe,
floor standpipe, or laundry tub. Select the method you need.
Floor standpipe drain system
114 mm
(4.5")
Minimum diameter for a standpipe drain: 51 mm (2"). Minimum
carry-away capacity: 64 L (17 gal.) per minute. Top of standpipe
must be at least 990 mm (39") high; install no higher than
1.22 m (48") from bottom of washer. If you must install higher
than 1.22 m (48"), you will need a sump pump system.
Wall standpipe drain system
114 mm
(4.5")
See requirements for floor standpipe drain system.
Floor drain system
Floor drain system requires a Siphon Break Kit (Part Number
285834), 2 Connector Kits (Part Number 285835), and an
Extension Drain Hose (Part Number 285863) that may be
purchased separately. To order, please contact the dealer from
whom you purchased your washer or an authorized service
company. Minimum siphon break: 710 mm (28") from bottom
of washer. (Additional hoses may be needed.)
Laundry tub drain system
114 mm
990 mm
(4.5")
Minimum capacity: 76 L (20 gal.).
IMPORTANT:
Top of laundry tub must be at least 990 mm (39") above floor;
n
install no higher than 1.22 m (48") from bottom of washer.
To avoid siphoning, no more than 114 mm (4.5") of drain hose
n
should be inside standpipe or below the top of wash tub.
Secure drain hose with cable tie.
990 mm
(39")
(39")
Electric Requirements
A 220–240 V, 50/60 Hz., AC-only, 10-amp, fused electrical supply
n
is required. A time-delay fuse or circuit breaker is recommended.
It is recommended that a separate circuit breaker serving only this
appliance be provided.
This washer is equipped with a power supply cord having
n
an earthing plug. If the supply cord is damaged, it must be
replaced by the manufacturer, a qualified service agent,
or other qualified person to avoid a hazard.
To minimize possible shock hazard, the cord must be plugged
n
into a mating, earthing-type outlet, earthed in accordance with
local codes and ordinances. If a mating outlet is not available,
it is the personal responsibility and obligation of the customer
to have the properly earthed outlet installed by a qualified
electrician.
If codes permit and a separate earth wire is used, it is
n
recommended that a qualified electrician determine that
the earth path is adequate.
Do not earth to a gas pipe.
n
Check with a qualified electrician if you are not sure the
n
washer is properly earthed.
Do not have a fuse in the neutral or earth circuit.
n
When in the installed position, the mains plug must be
n
accessible for disconnection.
If the supply cord is damaged, it must be replaced by the
n
manufacturer, its service agent, or similarly qualified persons
in order to avoid a hazard.
EARTHING INSTRUCTIONS
This washer must be earthed. In the event of a malfunction
or breakdown, earthing will reduce the risk of electric
shock by providing a path of least resistance for electric
current. This washer is equipped with a cord having an
equipment-earthing conductor and an earthing plug. The
plug must be plugged into an appropriate outlet that is
properly installed and earthed in accordance with all local
codes and ordinances.
WARNING:
Improper connection of the equipment-
earthing conductor can result in a risk of electric shock.
Check with a qualified electrician or serviceman if you are in
doubt as to whether the appliance is properly earthed.
Do not modify the plug provided with the appliance – if it will
not fit the outlet, have a proper outlet installed by a qualified
electrician.
5