Whirlpool 7MWTW1709DM0 Інструкція з використання та догляду - Сторінка 4

Переглянути онлайн або завантажити pdf Інструкція з використання та догляду для Пральна машина Whirlpool 7MWTW1709DM0. Whirlpool 7MWTW1709DM0 32 сторінки.

Друкувати сторінку

CONTROL PANEL AND FEATURES

Not all features and options are available on all models.

Appearance may vary.

LOAD SiZE

Select the setting most suitable for your load. Small

will add a low amount of water for smaller loads and Ex

Large will add the most amount of water for large or bulky

loads. Items need to move freely. Tightly packing can lead to

poor cleaning performance and may increase wrinkling and

tangling.

WASH

TEMP

Wash Temp senses and maintains uniform water

temperatures

by regulating incoming hot and cold water.

Select a wash temperature

based on the type of fabric

and soils being washed. For best results and following

the garment label instructions,

use the warmest wash

water safe for your fabric.

• On some models and cycles, warm and hot water may

be cooler than your previous washer.

• Even in a cold and cool water wash, some warm water

may be added to the washer to maintain a minimum

temperature.

WASH

CYCLE

KNOB

Use the Wash Cycle knob to select cycles on your washer.

Knob does not advance during the progress of the cycle,

see cycle status lights for each stage of the process. See

"Cycle Guide" for detailed descriptions

of cycles.

RINSE

OPTIONS

The following options may be added to most cycle.

See "Cycle Guide" for additional details.

1 RINSE

This option is used to limit a cycle to one rinse.

2 RINSES

This option can be used to automatically

add a

second rinse to most cycles.

1 RINSE with SOFTENER

This option must be selected if using fabric softener

during a cycle. It ensures that fabric softener is added

at the correct time in the rinse for even distribution.

2 RINSES

with SOFTENER

This option turns on both the Fabric Softener and

the 2 Rinses option.

START/PAUSE

BUTTON

Press to start the selected cycle; press again to pause the

cycle and unlock the lid. Press and hold for 3 seconds

to cancel a cycle.

NOTE: if the washer is spinning, it may take several

minutes to unlock the lid.

CYCLE

STATUS

LIGHTS

iNDiCATOR

Progress

C_)

([_)

Fitl

Wash

Rinse

Spin

Done

Locked

The Cycle Status Lights show the progress of a cycle.

At each stage of the process, you may notice sounds or

pauses that are different from traditional washers.

FILL

When the START/Pause button is pressed, the washer will

fill to the selected water level. If the lid is closed when the

washer is done filling the lid will lock and the washer will

begin operation.

If the lid is open when the water stops entering the

washer, the cycle will not begin until the lid has been

closed and the START/Pause button is pressed. If the

cycle has not been started within 10 minutes of the water

filling the washer, the washer will pump out the water.

NOTE: Avoid opening lid during sensing phase. The

sensing process will start over when the washer is

restarted. The FILL light may also come on during the

Soak and Wash portions of the cycle. This is normal. To

restart the washer after the lid has been opened press

START.

WASH

You will hear the agitator moving the load. The motor

sounds may change at different stages in the cycle.

The wash time is determined by the selected soil level.

RINSE

You will hear sounds similar to the wash cycle as the

washer rinses and moves the load. You may hear the

motor turning on briefly (short hum) to move the basket

while filling. Fabric softener will be added if the 1 Rinse

with Softener or 2 Rinses with Softener option was

selected.

Some cycles use spray rinsing. After draining and

spinning out wash water, the washer will continue to

spin and spray in rinse water for the entire rinse time.