Whirlpool AWO/D 43115 Схема програми - Сторінка 2
Переглянути онлайн або завантажити pdf Схема програми для Пральна машина Whirlpool AWO/D 43115. Whirlpool AWO/D 43115 2 сторінки. Washing machine frontloader
Також для Whirlpool AWO/D 43115: Посібник з експлуатації (21 сторінок)
Друкувати сторінку
CONSUMPTION DATA
Temperature
Programme
Cotton
Cotton***
Cotton
Synthetics
Synthetics
Delicates
Daily load
Quick wash
Wool
Handwash
Lingerie
Consumption values were measured in normalized conditions in compliance with Standard IEC/EN 60 456. Consumption
data in the home may vary with respect to the values in the table in relation to the water supply pressure and temperature,
the load and the type of wash.
*
The remaining time indicator can deviate from the values in the table, because it takes into account the household
conditions applicable at that time.
**
To reduce the water temperature, some cold water is added at the end of the main wash cycle, before the pump drains
the water out.
*** Reference Programme for Energy Label.
ADD DETERGENTS, CLOSE THE DOOR
AND SELECT THE PROGRAMME
Add detergent as indicated on the front page and as
described in your Instructions for Use. Close the door
and turn the programme selector to the desired
programme and temperature. The indication lamp
next to the "Start/Pause" button
SELECT ANY DESIRED OPTION
Push the button(s) of any option(s) desired - the
respective indication lamp lights up.
When the combination of programme and additional
option(s) is not possible, the indication lights switch
off automatically. Unsuitable combinations of options
are deselected automatically.
"Prewash" button
• Only for heavily soiled loads (for example sand,
granular dirt) sensible. Increases the cycle time
by approximately 15 min.
Downloaded From WashingMachine-Manual.com Manuals
Load
Water
Energy
(°C)
(kg)
(l)
(kWh)
95
5.0
49**
1.90
60
5.0
44
0.85
40
5.0
44
0.60
60
2.5
50**
0.70
40
2.5
45
0.55
30
1.5
50
0.50
40
3.0
45
0.45
30
3.0
40
0.40
40
1.0
55
0.60
40
1.0
45
0.60
30
1.0
45
0.50
"Cold wash" button
• Water is heated only up to 20°C
• Suitable for delicate laundry items with wash
temperature recommendation of max. 30° on
the care label.
• Selectable only on the lowest temperature step
flashes.
of each programme.
"Easy ironing" button
• Can be used together with "Cotton"
"Synthetics"
and "Daily load"
programmes to make ironing easier.
• Increases the water quantity and the clothes are
spun very gently.
"Variable spin" button
• Every programme has a predefined spin speed.
• Press the button to set another spin speed.
• If spin speed "0" is selected, the final spinning is
cancelled but intermediate spin peaks remain
during rinse. The water is drained out only.
PROGRAMME START
Open the tap and press the "Start/Pause" button
Approx. Programme
The indication lamp next to the "Start/Pause" button
Duration
(hours : minutes)*
lights up. The programme sequence indicator
2:00
shows the current programme phase, running from left
2:20
to right through Wash, Rinse, Spin/Drain.
2:00
• When the programme phase is finished, the
1:30
corresponding indication goes out.
1:15
"DOOR OPEN" INDICATION
0:45
1:00
Before starting and after end of a programme, the
0:30
lamp lights to show that the door can be opened. As
0:45
long as a wash programme is running, the door
0:40
remains locked and must on no account be forced
0:40
open. In case you have an urgent need to open it
during a running programme, refer to "Cancel
(Reset) a running programme before the end".
RED INDICATIONS
"Service"
Lighting up of the "Service" indication can be caused by
a fault in an electrical component. Refer to the
"Troubleshooting Guide" in your Instructions for Use;
if the fault persists, contact our After Sales Service.
"Water tap closed"
The appliance has no or insufficient water supply.
Open the water tap; if the indication still lights up,
refer to the "Troubleshooting Guide" in the
,
Instructions for Use.
"Clean pump"
Waste water is not pumped out. Check whether the
drain hose is kinked or the filter must be cleaned; in
the latter case refer to the Instructions for Use
("Removing the Filter").
PROGRAMME END
.
• All the lights of the programme sequence
indicator are off, and the "Door open"
indication
lights up.
1. Turn the programme selector to the "Off/O"
position.
2. Close the water tap.
3. Open the door and unload the machine.
4. Leave the door ajar to allow the drum to dry.
CHANGE PROGRAMME AND/OR OPTIONS
AFTER PROGRAMME START
1. Press the "Start/Pause" button
the programme. The light flashes.
2. Select the new programme (with temperature),
any options and another spin speed if you want.
3. Press the "Start/Pause" button
new programme continues at the same position
where the previous programme was interrupted.
Do not add detergent for this programme.
CANCEL (RESET) A RUNNING
PROGRAMME BEFORE THE END
The "Reset" button
cancels a programme
before the end.
• Press the "Reset" button
for at least 3
seconds. Any existing water is drained out
before the door can be opened.
Whirlpool is a registered trademark of Whirlpool USA
5019 301 10258/A
to pause
again. The