Whirlpool AWO45100 Посібник користувача програми - Сторінка 4
Переглянути онлайн або завантажити pdf Посібник користувача програми для Пральна машина Whirlpool AWO45100. Whirlpool AWO45100 4 сторінки.
Друкувати сторінку
95
60
40
40
Daily Wash
40
30
Silk/Delicates
30
40
Hand Wash
40
Big Items
40
Lingerie
40
95° Antibacterial
95
Drum Clean
60
The actual running time can deviate from the values in the table, because it takes into account the operating conditions applicable at that time.
Reference programme for Energy and Water Labelling, according to the IEC EN60456.
To reduce water temperature, some cold water is added at the end of the main wash cycle, before the pump drains the water out.
The detergent can also be added as a solution dissolved in
warm water. (Always use high efficiency, low foam detergent for
front load washing machine.)
Press the selected option button once, the current value is
displayed on the display. By pressing the button repeatedly, the
display will display the values in sequence. By pressing the
button of the desired option, the respective indicator lights up.
When the combination of programme and additional options is
not possible, the indication lights switch off automatically.
Unsuitable combinations of options are deselected automatically.
"Wash Time" button:
• The wash time can be adjusted by pressing the button.
Each press of the button either increases or decreases
the time by approximately 10 minutes, depending on the
Wash Programme selected.
"Prewash" button:
• Suitiable for heavily solided loads(for example with sand and
dust) and the programme duration is prolonged for 18 minutes.
5.5
2:15
5.5
2:10
5.5
1:59
2.0
1:15
2.5
0:50
2.0
0:17
1.5
0:40
1.0
0:46
0:40
5.5
1:59
1.0
0:40
5.5
2:15
1:10
"Rinse Hold" button:
• The laundry remains in the last rinse water without
progressing to the final spin cycle, to avoid creasing of
the laundry.
• Do not leave the laundry to soak for too long in the
"Rinse Hold" state, to prevent colours from being
affected.
• The programme stops at "Rinse Hold" when the
"Rinse Hold" light in the programme sequence
indication is on. Also, the indication lamp next to the
"Start / Pause" button flashes.
• To terminate "Rinse Hold", by spinning the laundry,
press the "Variable Spin" button to select the desired
spin speed and then press the "Start / Pause" button.
The programme will then terminate automatically after
the spin cycle.
• To terminate "Rinse Hold" and drain the water,
without any spinning, press the "Start / Pause"
button. Or, turn the programme selector knob to the
"Drain" programme and press the "Start / Pause"
button.
"Variable Spin" button:
• Every programme has a pre-defined max. spin speed.
• Press the button to set another spin speed.
• If spin speed "0" is selected, the final spin is cancelled,
but intermediate spin peaks remain during the rinse
cycle. Only the water is drained out.
TEMPERATURE CONTROL
On selecting a programme, a predefined temperature
is displayed. Press the button to set another
temperature.
START DELAY
The "Start Delay" function allows the machine to be
run at the consumer's convenience, for example at
night when electricity is cheaper.
• Select the programme, temperature and the required
options.
• Press the "Start Delay" button to select one of the
delay time steps between 0:10 and 23:00 hours.
• Press the "Start / Pause" button.
• The LED display above the "Start Delay" button,
displays the delay time and the countdown begins.
• The time delay indication disappears when the
programme starts and is replaced by the remaining
programme time.
• To change the time delay, once the "Start / Pause"
button has been pressed, press the "Start / Pause"
button and then press the "Start Delay" button to
select the required time delay.
To Cancel "Start Delay":
To cancel the Start Delay, do one of the following:
• Turn the programme selector to another position, or;
• Press the "Start / Pause" button, or;
• Press the "Reset" button for at least 3 seconds, the
"Start Delay" time disappears from the time display.
PROGRAMME START
Open the tap and press the "Start / Pause" button.
The indication lamp next to the "Start / Pause" button
lights up. The programme sequence indicator shows
the current programme phase, from left to right, as
Prewash, Wash, Rinse, Rinse Hold and Spin / Drain.
The time display shows the remaining programme
time. Due to variations in load and the temperature of
the inlet water, the remaining time is re-calculated in
certain programme phases. When this occurs, the
remaining programme time is replaced by an
animation.
Before the start and after the end of a programme, the
"Door Open" indication lamp, lights to show that the
door can be opened. While a wash programme is
running, the door remains locked and must on no
account be forced open. In case, there is an urgent
need to open it during a running programme, press the
"Start / Pause" button and then press the "Reset"
button.
CANCEL / RESET A RUNNING
Refer to "
PROGRAMME BEFORE THE END
".
RED FAILURE INDICATIONS
"Water Tap Closed":
If the appliance has insufficient or no water supply, the
"Water Tap Closed" indication will light up. Open the
water tap. If the indication still lights up, refer to the
"Trouble Shooting Guide" in the Instructions for Use.
"Clean Pump":
If the waste water is not being pumped out, the "Clean
Pump" indication will light up. Check whether the drain
hose or the filter requires to be cleaned. In the latter
case, refer to, "Removing the Filter" in the Instructions
for Use.
• The display shows "End", along with an audible signal,
and the "Door Open" indication lights up.
• All the lights of the programme sequence indicators
are off.
1. Turn the programme selector to the "Off / 0" position.
2. Close the water tap.
3. Open the door and unload the machine.
4. Leave the door ajar, to allow the drum to dry.
CHANGE PROGRAMME AND / OR
OPTIONS AFTER PROGRAMME START
1. Press the "Start / Pause" button to pause the
programme. The indication light flashes.
2. Select the new programme, the temperature, options
and the required spin speed.
3. Press the "Start / Pause" button again. The new
programme continues at the same position, where
the previous programme was interrupted. Do not add
detergent again.
CANCEL / RESET A RUNNING
PROGRAMME BEFORE THE END
The "Reset" button cancels a set programme before
the end of the cycle. To reset, press the "Reset" button
for at least 3 seconds. Water from the machine is then
drained out, before the door can be opened.
W10342032A