Whirlpool 3XARG475WP2 Інструкція з використання та догляду - Сторінка 2

Переглянути онлайн або завантажити pdf Інструкція з використання та догляду для Холодильник Whirlpool 3XARG475WP2. Whirlpool 3XARG475WP2 10 сторінок.

Друкувати сторінку

English

Eu :

KNOW YOUR FROST FREE APPLIANCE

The main advantage

of your refrigerator/freezer

with fan

circulation is the total absence of frost and ice forming on the

compartments

walls, thanks to the process described below.

The cold air is produced by an evaporator

and is circulated by

means of a fan into the two compartments.

The air, having been circulated, is again passed to the evaporator.

This keeps the humidity low. In this way, there will be no frost

formation

on <the compartment

walls, as in a traditional

appliance.

The "ventilated cold" system ensures a better storage of foods

maintaining their original condition for a longer period of time.

DESCRIPTION

OF THE APPLIANCE

(Fig. 1)

A - Ice cube trays (not shown)

6 - Ice bin

C - Freezer shelf

D - Refrigerator control

E - Model and serial number plate (on side wall)

F - Exterior moisture control

G - Light

H - Freezer control

I - Meat drawer

L - Crisper cover

M - Crisper humidity control

N - Crispers

0 - Levelling rollers (not shown)

P - Base grille

Q - Shelf guides

R - Utility compartment

S - Butter compartment

T - Utility bin

U - Adjustable

door bins

V - Adjustable

glass shelves

INSTALLATION

(Fig. 2)

Please check your appliance and ensure that it is undamaged;

any transport damage must be reportedto

your dealer within

24 hours of receipt.

The appliance

should not be installed close to heat sources

such as cookers, central heating boilers, direct sunlight, etc.

It must however be located in a well ventilated dry space.

Allow 1 cm space on each side and at the top of the refrigerator

for ease of installation.

If the refrigerator is to be against a wall, you might want to leave

extra space on the hinge side so the door can be opened

wider.

Level the appliance

proceeding

as follows (Fig. 3-4):

- Remove the base grille by pulling it outwards.

- Level the appliance by means of screw A. To raise turn screw

clockwise.

Remount the grille as follows:

1. Line up the grille support tabs C with the metal clips D.

2. Push firmly to snap into place.

Clean the interior with a sponge dampened

in a solution of

lukewarm water and bicarbonate

of soda or vinegar.

Clean the exterior with a sponge dampened

in a solution of

lukewarm water and dry with a soft cloth.

Do not use abrasives, detergents

or harsh cleansers.

Mount the internal accessories

(Fig. 1).

ELECTRICAL

CONNECTION

AND

OPERATION

This appliance

conforms

to EEC directive

87/308 on radio-

interference.

Leave the appliance to stand for one hour before connecting

it to the electricity supply. Please check that the voltage on the

rating plate (Fig. 5) corresponds

to the voltage in your home

(220/240 v).

The earthing

of this appliance

is compulsory

by law.

The Manufacturer will accept no liabilityfordamage

to persons

or objects arising from the non-observance

of this requirement.

If the plug and the wall socket do not comply, have the socket

replaced by a qualified electrician.

He should also check that the section of the socket wires can

withstand the power absorbed

by the appliance.

The use of the adapters, multiple sockets and extension cords

is not advisable.

If absolutely

necessary, use simple or multiple adapters and

extension

cords in compliance

with local safety regulations,

paying

attention

not to exceed

the maximum

amperage,

which is marked on the simple adaptors

and on extension

cords and that of the total power marked on the multiple

adapters.

For UK only

Electrical

information

WARNING -THIS APPLIANCE MUST BE EAFITHED

FUSE REPLACEMENT

If the mains lead of this appliance is fitted with a BS 1363A 13 amp

fused plug, to change a fuse in this type of plug use an A.S.T.A.

approved fuse to BS 1362 type and proceed as follows:

1. Remove the fuse cover (A) and fuse (B)

2. Fit replacement

13A fuse into fuse cover

3. Refit both into plug.

IMPORTANT:

The fuse cover must be refitted when chang-

ing a fuse and if the fuse cover is lost the plug must not be used

until a correct replacement

is fitted. Correct replacements

are

identified by the colour insert or the colour embossed in words

on the base of the plug.

Replacement fuse covers are available from your local electrical

store.

Connection

to a rewireable

plug

If the fitted plug is not suitable for your socket outlet, then it

should be cut off and disposed of in order to avoid a possible

shock hazard should it be inserted into a 13A socket else-

where. A suitable alternative plug should then be fitted to the

cable.

The wires in this mains lead are coloured in accordance

with

the following code:

BLUE "NEUTRAL"

('IN")

BROWN "LIVE" ("L")

GREEN AND YELLOW "EARTH" ("E)

1. The GREEN AND YELLOW wire must be connected

to the

terminal in the plug which is marked with the letter "E" or by the

Earth symbol

& or coloured green or green and yellow.

2. The BLUE wire must be connected to the terminal which is

marked with the letter "N" or coloured black.

3. The BROWN wire must be connected to the terminal which

is marked with the letter "L" or coloured red.