Whirlpool 240-VOLT ELECTRIC DRYER Посібник з використання та догляду - Сторінка 11
Переглянути онлайн або завантажити pdf Посібник з використання та догляду для Сушарка Whirlpool 240-VOLT ELECTRIC DRYER. Whirlpool 240-VOLT ELECTRIC DRYER 32 сторінки. 240-volt electric dryer
Також для Whirlpool 240-VOLT ELECTRIC DRYER: Інструкція з використання та догляду (20 сторінок), Інструкція з використання та догляду (33 сторінок), Посібник з використання та догляду (24 сторінок), Посібник з використання та догляду (24 сторінок)
Друкувати сторінку
The control panel is simple to understand and easy to operate.
The illustrations below define the knobs and buttons, and the
paragraphs define the purpose of each.
Power
This button switches the power to the machine on and off. The
indicator light will glow to indicate the power is on.
Indicator Light
This light indicates when the power is on or that a cycle has
started.
Temperature
The Temperature Control button lets you select between a normal
and low drying temperature.
NOTE: Always refer to the care label on the garment to determine
whether it can be tumble dried.
Normal
The Normal temperature setting is for sturdy fabrics, such as
cotton, linen and denim. If the Temperature Control button is not
pressed in, the temperature setting is Normal.
Low
The Low setting is for synthetics, such as cotton/polyester blend,
rayon, acetate, washable silk or nylon. If the Temperature Control
button is pressed in, the temperature setting is Low.
Cycle Knob
Turn this knob to the recommended setting. Indicator light will
flash to indicate a cycle has been selected. See "Drying, Cycle
and Temperature Tips."
Controls
Stop Position
Turn the cycle knob to the Stop position at any time.
Start Button
After you have selected a cycle and temperature, press this
button to start the cycle. Indicator light will glow to indicate the
cycle has started.
Drying, Cycle and Temperature Tips
Select the correct cycle and temperature for your load.
Your dryer tumbles the load without heat during the last few
minutes of all cycles to make the load easier to handle and to
reduce wrinkling. After the cool-down cycle ends, the light
flashes, and an end-of-cycle signal sounds to indicate the cycle
is complete.
Drying tips
Follow care label directions when they are available.
Remove the load from the dryer as soon as tumbling stops to
reduce wrinkling. This is especially important for permanent
press, knits and synthetic fabrics.
Avoid drying heavy work clothes with lighter fabrics. This
could cause overdrying of lighter fabrics, leading to increased
shrinkage or wrinkling.
Cycle and temperature tips
Dry most loads using an automatic cycle.
Line dry bonded or laminated fabrics.
NOTE: If you have questions about drying temperatures for
various loads, refer to the care label directions.
Automatic Cycles
When you are using the Auto Moisture Sensing Cycle, two metal
strips (sensors) located on the dryer baffles determine the
dryness of the load. The metal strips help detect the amount of
moisture left in the clothes as they pass. When there is moisture
left in the clothes, the machine will continue to run. As clothes
begin to dry, the amount of water left in the clothes decreases,
and the timer advances through the remainder of the cycle. When
the selected dryness level is reached, the dryer goes into a cool
down period of up to 15 minutes.
Automatic cycles may be used for most loads. Automatic cycles
give the best drying results in the shortest time. Drying time
varies according to the type of fabric, size of the load and
dryness setting.
After drying a load, check the dryness.
If the load is drier than you like, select a setting closer to Less
Dry the next time you dry a similar load.
If a load is not as dry as you like, complete drying using a
Timed cycle. Select a setting closer to More Dry the next time
you dry a similar load.
Cycles
11