Whirlpool 27' Інструкція з монтажу - Сторінка 3

Друкувати сторінку

grounding wire). The fiedble, armored

cable extending from the appliance

should be connected

dire&+ to the

iunctbn box.

Locate the junction box to

m allow as much slack CIS oossible

between the Junction box an'd ihe

appliance

so that the oven con be

moved if servicing is ever necessoly.

Do Not cut the conduit.

A U.L:listed conduit connector

must

be provided at the Junction box.

ii is the personal responsibility

. and obligation

of the

customer to contact

a quoliWd

electWan

to assure that me electial

installation b odequote

and In

confomance

VJim the Naiional

ElectrIcal Code ANWNFPA 7&k&&

edition.' and all local codes and

ordinances.

Copies of me standard listed may be

obtained

from:

' National Fire Prdeclion

Association

Botterymarch

Pati

Quincy,

Massachusetts

02269

A tiring diagram $ Included In

. the Tech

Sheet.

The Tech Sheet

is located on bottom. behind the

lower vent grill.

Electrical

connection

Electrical

Shock

Hozord

* Eledrtcal

ground

is required

this appliance.

- Do Not connect

to the electrical

supply

until

appliance

permanently

grounded.

* Dtsconnecl

power

to the junction

box

before

making

the electrical

connedion.

. This appliance

must

connected

lo o grounded,

metallic.

permanent

wiring

system.

or o grounding

connector

should

be connected

to the grounding

terminal

or wire

lead

on Ihe appliance.

Failure

to do so could

result

In Q

fire, personal

injury

or electrical

shock.

lhls appliance

Is manufactured

him

white (neutra0 power supply wire and (

cabInetconnected.

ereen grounding

tie

lwkbd

together.

Connect

the

appliance

cable to the Jundon bow

throuah the U.L-llsted conduit

con&&tor.

Complete

elecirlcal

connection

according

to your

lnstotlatkn needs.

B. Where local codes

DO NOT permit...

Connecting

the cabinet-grounding

conductor

to the neuiral

(white)

junction

box

wire:

Cab!+ horn

power wpply

J""t,lo"

Cob,.

A: Where

local codes

permit...

.'-

Contiecttng

the cablnel-grounding

condudor

lo the neutral

(whtte)

junction box wire:

Cabk

horn

Jundlon

power supply

1. Turn power

supply

off.

2. Connect

three wires: green and

white appliance

cable wires and the

white wire

the iunction box.

3. Connect

the two black tires

together;

then the two red wires

together.

(See Figure 1.)

Now start...

With

oven

in kitchen.

Remove shlpping materials and

. protective

film from microwove

oven and

oven.

Do Not remove the

loom

shipping

base

d Ihb time.

Figure

from O"."

1. Turn power

supply

On.

2. Connect the tiie

appliance

cable tire to the neutral (whiie) wire

in Junct!on box.

3. Connect the Iwo black tires

together; men me two red wires

together.

(see

figure 2.)

4. Connect the grounding wire to o

grounded wire in the junction box or

to a grounded. copper cold water

Completely

open oven door.

. Remove two oven door screws.

Remove and unwrap racks

. and omer parts from inside oven.

Remove the air grille taped to

me top

or side of oven.

A separate copper grounding wire

(No.-10 minimum) MUST be connected

io a grounded metal cdd water pipe

by means of a clomp and then to the

external grounding connector

screw.

Do Nd ground to a gas supply pipe OT

hol waler

plpe.

Do Not connect

electrical suppk until appliance

pemanentty

grounded.

(see Flgure

3.)

C. If connecting

to a four-

wire electrical

system...

Do Not connect

the cabinet

grounding

conductor

lo the neutral

(white)

Junction

box wire.

Cabl.

horn

POW.'IUPPlY

Figure

cab!.

from 0°C."

1. Turn power

supply

ott.

2. Separate

the green and white

appliance

cable wires.

3. Connect

the white oppllance

cable wire to the neutral (white) wire

in the junction

box.

4. Connect

the two black wires

together:

then ihe hue red wires

together.

(See Figure 4.)

5. Connect

the green appliance

cable wire to the green grounding

wire in the Junction box.

Personal

Injury

Hazard

Use both

hands

to remove

oven

door.

. Grasp

onty the sides

of the oven

door.

. Do Not use handle

or any

portion

ot the hont

hame

or him for lining.

. Because

ot the weight

ond she

of the oven,

two or more

people

ore needed

to move

and

solety

install

oven.

Failure

to properly

grasp

the oven

door

or to Iti7 oven

property

could

resutl

in damage

lo product

personal

injury.

Close oven door to me broil

. position. Grasp lhe skies of the

oven door and pull the door up and

off the hinges to remove. Set dmr

aside.

Before

moving

oven

acrass

floor.

check

thoi

oven

is on shipping

base

or Me

oven

onto

cardboard

or hardtird.

Failure

to follow

these

instructions

may

resuli

in danoge

to floor

coverinq.

Turn power supply off. Move

. oven close to final oosition.

Remove and discord shipping base,

cardboard

or hardbwrd.

Feed

appliance

cable through opening in

cabinet. Make electlical conn@fions.

See Electrical requirements

and

ElecMcol connechon

sections. Panels A

and 8.

Panel