Whirlpool 3RLEC8600 Посібник з використання та догляду - Сторінка 11
Переглянути онлайн або завантажити pdf Посібник з використання та догляду для Сушарка Whirlpool 3RLEC8600. Whirlpool 3RLEC8600 12 сторінок. Electric and gas dryers
Також для Whirlpool 3RLEC8600: Інструкція з використання та догляду (12 сторінок), Інструкція з монтажу Посібник з монтажу (8 сторінок), Інструкція з монтажу Посібник з монтажу (8 сторінок), Інструкція з монтажу Посібник з монтажу (8 сторінок)
Друкувати сторінку
Clothes are not drying satisfactorily, drying times are too
long, or load is too hot
Is the lint screen clogged with lint?
Lint screen should be cleaned before each load.
WARNING
Fire Hazard
Use a heavy metal vent.
Do not use a plastic vent.
Do not use a metal foil vent.
Failure to follow these instructions can result in death
or re.
Is the exhaust vent or outside exhaust hood clogged with
lint, restricting air movement?
Run the dryer for 5-10 minutes. Hold your hand under the
outside exhaust hood to check air movement. If you do not
feel air movement, clean exhaust system of lint or replace
exhaust vent with heavy metal or exible metal vent. See the
Installation Instructions.
Are fabric softener sheets blocking the grille?
Use only one fabric softener sheet, and use it only once.
Is the exhaust vent the correct length?
Check that the exhaust vent is not too long or has too many
turns. Long venting will increase drying times. See the
Installation Instructions.
Is the exhaust vent diameter the correct size?
Use 102 mm (4") diameter vent material.
WARNING
Explosion Hazard
Keep ammable materials and vapors, such as petrol,
away from dryer.
Place dryer at least 460 mm (18 inches) above the oor
for a garage installation.
Failure to do so can result in death, explosion, or re.
Is the dryer located in a room with temperature below
7ºC (45ºF)?
Proper operation of dryer cycles requires temperatures above
7ºC (45ºF).
Dryer Results
Is the dryer located in a closet?
Closet doors must have ventilation openings at the top and
bottom of the door. The sides and front of the dryer require a
minimum of 25 mm (1") of airspace, and the rear of the dryer
requires 127 mm (5"). See the Installation Instructions.
Has an air dry cycle been selected?
Select the right cycle for the types of garments being dried.
Is the load too large and heavy to dry quickly?
Separate the load to tumble freely.
Cycle time too short
Use two or more people to move and install dryer.
Failure to do so can result in back or other injury.
Is the automatic cycle ending early?
Change the load type setting on Automatic Cycles.
Increasing or decreasing the dryness level will change the
amount of drying time in a cycle.
Lint on load
Is the lint screen clogged?
Lint screen should be cleaned before each load.
Stains on load or drum
Was dryer fabric softener properly used?
Add dryer fabric softener sheets at the beginning of the cycle.
Fabric softener sheets added to a partially dried load can
stain your garments.
Drum stains are caused by dyes in clothing (usually blue
jeans). This will not transfer to other clothing.
Loads are wrinkled
Was the load removed from dryer at the end of the cycle?
Was the dryer overloaded?
Dry smaller loads that can tumble freely.
Odors
Have you recently been painting, staining, or varnishing
in the area where your dryer is located?
If so, ventilate the area. When the odors or fumes are gone
from the area, rewash and dry the clothing.
Is the electric dryer being used for the rs t time?
The new electric heating element may have an odor. The
odor will be gone after the r st cycle.
WARNING
Excessive Weight Hazard
11