Whirlpool 8578230 Інструкція з монтажу Посібник з монтажу - Сторінка 12

Переглянути онлайн або завантажити pdf Інструкція з монтажу Посібник з монтажу для Сушарка Whirlpool 8578230. Whirlpool 8578230 32 сторінки. 27" (69 cm) electric dryer

Друкувати сторінку

Periscope Installation (For use with dryer vent to wall vent

mismatch):

Part Number 4396037 - 0" (0 cm) to 18" (45.72 cm) mismatch

Part Number 4396011 - 18" (45.72 cm) to 29" (73.66 cm)

mismatch

Part Number 4396014 - 29" (73.66 cm) to 50" (127 cm)

mismatch

Special provisions for mobile home installations

The exhaust vent must be securely fastened to a noncombustible

portion of the mobile home structure and must not terminate

beneath the mobile home. Terminate the exhaust vent outside.

Determine vent path

Select the route that will provide the straightest and most

direct path outdoors.

Plan the installation to use the fewest number of elbows and

turns.

When using elbows or making turns, allow as much room as

possible.

Bend vent gradually to avoid kinking.

Use the fewest 90° turns possible.

Determine vent length and elbows needed for best drying

performance

Use the following Vent system chart to determine the type of

vent material and hood combinations acceptable to use.

NOTE: Do not use vent runs longer than those specified in the

Vent system chart. Exhaust systems longer than those

specified will:

Shorten the life of the dryer.

Reduce performance, resulting in longer drying times and

increased energy usage.

The Vent system chart provides venting requirements that will help

to achieve the best drying performance.

Vent system chart

NOTE: Side and bottom exhaust installations have a 90º turn

inside the dryer. To determine maximum exhaust length, add one

90º turn to the chart.

Number of

Type of

90º turns

vent

or elbows

Rigid metal

Flexible metal

Rigid metal

Flexible metal

Rigid metal

Flexible metal

Rigid metal

Flexible metal

Rigid metal

Flexible metal

Install Vent System

1. Install exhaust hood. Use caulking compound to seal exterior

wall opening around exhaust hood.

2. Connect vent to exhaust hood. Vent must fit inside exhaust

hood. Secure vent to exhaust hood with 4" (10.2 cm) clamp.

3. Run vent to dryer location. Use the straightest path possible.

See "Determine vent path" in "Plan Vent System." Avoid 90º

turns. Use clamps to seal all joints. Do not use duct tape,

screws or other fastening devices that extend into the interior

of the vent to secure vent.

Install Leveling Legs

WARNING

Excessive Weight Hazard

Use two or more people to move and install dryer.

Failure to do so can result in back or other injury.

1. To protect the floor, use a large, flat piece of cardboard from

the dryer carton. Place cardboard under the entire back side

of the dryer.

2. Firmly grasp the body of the dryer (not the top or console

panel). Gently lay the dryer on the cardboard. See illustration.

3. Examine the leveling legs. Find the diamond marking.

4. Screw the legs into the leg holes by hand. Use a wrench to

finish turning the legs until the diamond marking is no longer

visible.

5. Place a carton corner post from dryer packaging under each

of the 2 dryer back corners. Stand the dryer up. Slide the

dryer on the corner posts until it is close to its final location.

Leave enough room to connect the exhaust vent.

Box or

Angled

louvered

hoods

64 ft (20 m)

58 ft (17.7 m)

36 ft (11 m)

28 ft (8.5 m)

54 ft (16.5 m)

48 ft (14.6 m)

31 ft (9.4 m)

23 ft (7 m)

44 ft (13.4 m)

38 ft (11.6 m)

27 ft (8.2 m)

19 ft (5.8 m)

35 ft (10.7 m)

29 ft (8.8 m)

25 ft (7.6 m)

17 ft (5.2 m)

27 ft (8.2 m)

21 ft (6.4 m)

23 ft (7 m)

15 ft (4.6 m)