Whirlpool CEM2750JQ0 Посібник з монтажу - Сторінка 3

Переглянути онлайн або завантажити pdf Посібник з монтажу для Сушарка Whirlpool CEM2750JQ0. Whirlpool CEM2750JQ0 14 сторінок. Commercial gas/electric dryer

Друкувати сторінку

The console

houses the accumulator

timer with actuating

arm and button,

The timer is set to provide

45 minutes

(4 pins) of drying time when activated

by the coin slide. Timer cams for

30- minute (6 pins) and 60-minute

(3 pins) drying times are included

the parts bag,

The coin-slide

mechanism,

control

panel

lock and key, and coin-box

leck

and key are not included

and are

available

from usual industry sources.

To change to a

30- or 60-minute

timingcam

(for mechanical

timer

models

only)

Electrical Shock Hazard

Disconnect power before

making cam changes.

Failure to do so can result in

death or electrical shock.

Each coin-operated

dryer is

equipped

with a 45-minute

timer

cam that provides

45 minutes

drying time when activated

by the

coin slide.

You can install the 30-minute

60-minute

timing

cam (shipped

with

drye0

as follows:

I. Unlock meter case. Reach

into

control

panel

area,

2. Turn the timing

cam by hand

until

the "V" -shaped

notch

lines up

below the ratchet

tooth,

ralchet

looth

smlng

cam

ddve

Une u

lug

clear

ratchet

hub

tooth,

down

3. Insert a narrow,

fiat-blade

screwdriver

under

the timing

cam

near the clock

shaft. Gently

lift cam

straight up and off shatt making

sure that the _V + -shaped

notch

ctears the ratchet tooth.

4. Place new cam (hub side down)

over clock shaft. Line up fiat side of

shaft with flat side of cam hole,

Check

that drive lug is in place.

5. Turn cam

until "V" -shaped

notch

lines up with ratchet tooth,

6. Press cam down in place

on motor

shaft, Make sure that "V _ -shaped

notch

clears the ratchet

tooth.

7. Close and lock the meter case,

Exhaust

requirements

Fire Hazard

Use a heavy metal vent.

0o not use a plastic vent.

Do not use a metal foil vent.

Failure to do so can result In

death or fire.

Do not use non-metal

flexible vent,

metal

vent that is smaller than four

inches in diameter

or exhaust

hoods with

magnetic

latches.

The dryer must be exhausted

outdoors.

Do not exhaust

dryer into a gas vent,

chimney,

wall, ceiling,

or concealed

space

of a building.

Do not install flexible vent in enclosed

walls, ceilings or floors,

If using an existing exhaust

system, cleon

lint from entire length of exhaust system.

Make

sure exhaust

hood is not plugged

with lint.

The exhaust system should

be inspected

and cleaned

yearly,

Replace

any plastic or metal foil exhaust

vent with rigid metal

or flexible

metal

vent.

Use4"110.2 cm) ventclamps to

secureventsystem.

exhaust airl_w

Four-lnch 110.2 cm) metal exhaust vent

L_required,

Plan Installation

to use the

fewest

number

of elbows and turns.

Metalflexible ventmust be fully

extended and supportedwhen the

dryer is inits f inal p osition.

DO NOT

KINKOR CRUSH THEVENT,The metal

flexible ventmust be complelely

open to allow adequate exhaust air

to flow.

Allow as much room as possible

when using elbows or making turns.

Bend vent gradually to avoid kinking.

Remove excess flexible vent to avoid

sagging and kinking that may result in

reduced air flow,

Exhaustouflet is locatedatthe

centerofthe bottom dryer back.

The exhaustventcan be routedup,

down, left, fight, behindthe dryer or

straight outthe back ofthedryer.

Maxlmum length of exhaustsystem

depends upon thetype ofventused,

number ofelbows and typeof

exhausthood. The maximum length

forboth rigid and flexible

ventis

shown inthe chart,

EXHAUSTHOOD TYPE

(lO.2cm)

MAXIMUM LENGTH OF4-R4C1"1 (I 0,2 cm) _R

RIGIDMETAL VENT

64 FT. (19.S m)

58 FT.(17.7 m)

54 FT. (16.S m)

54 FT, (|6.S m)

48 FT.(14.6 m)

44 FT. (r3.4 m)

44 FT. (13.4 m)

38 FT.(11.6 m)

35 FT. (10.7 m)

29 FT.(8.8 m)

27 FT. (8.2 rn)

27 FT. (8.2 m)

21 FT.(6.4 m)

MAXIMUM LEFU_IH O f 4-INCH 110.2c:m)1_4AME11ER

FLEXIBLE METAL VENT

36 FT.(11.0 m)

36 FT.(11.Q m)

28 FT,[S,5 m)

31 FT.(9.4 n0

31FT, (9.4 m)

23 FT.(7.0 m)

27 FT.(8.2 m)

27 FT.(S.2 m)

19R. (S.S m)

25R, (7.6 m)

_5 FT.(7.6 m)

17 FT.(5.2 m)

23 FT.(7.0 m)

23 FT.(7.0 m]

15FT.(4.6 m)

Forexhaust systems notcovered by

theexhaustlength chart, see

Whirloool Service Manual °Exhausflng

Whirlpool D ryers/Part No.603197,

avaliable f rom yourWhirlpool p arts

distributor,

If dryer is Installed

In a confined area,

such as a

bedroom,

bothroom

closet, It must be exhausted

to the

outside and provision

made

for

enough

air for combustion

and

ventilation,

(Check

governing

codes

and ordinances.)

See "Recessed

area

and closet installation

instructions"

Page 12,

Page 3