Whirlpool DUET SPORT W10151580B Інструкція з використання та догляду - Сторінка 3

Переглянути онлайн або завантажити pdf Інструкція з використання та догляду для Сушарка Whirlpool DUET SPORT W10151580B. Whirlpool DUET SPORT W10151580B 28 сторінок. Duet sport electronic electric dryer

Друкувати сторінку

WARNING:

To reduce the risk of fire, electric shock, or injury to persons when using the dryer, follow basic precautions,

including the following:

Read all instructions before using the dryer.

Do not place items exposed to cooking oils in your dryer.

Items contaminated with cooking oils may contribute to

a chemical reaction that could cause a load to catch fire.

Do not dry articles that have been previously cleaned in,

washed in, soaked in, or spotted with gasoline, dry-

cleaning solvents, or other flammable or explosive

substances as they give off vapors that could ignite or

explode.

Do not allow children to play on or in the dryer. Close

supervision of children is necessary when the dryer is

used near children.

Before the dryer is removed from service or discarded,

remove the door to the drying compartment.

Do not reach into the dryer if the drum is moving.

Do not install or store the dryer where it will be exposed

to the weather.

Do not tamper with controls.

Gather the required tools and parts before starting installation.

Read and follow the instructions provided with any tools listed

here.

Flat-blade screwdriver

#2 Phillips screwdriver

Adjustable wrench that

opens to 1" (25 mm) or

hex-head socket wrench

(for adjusting dryer feet)

Wire stripper (direct wire

installations)

Level

Parts supplied

Remove parts packages from dryer drum. Check that all parts are

included.

Parts package.

4 Leveling legs

NOTE: Do not use leveling legs if installing the dryer on a

pedestal.

IMPORTANT SAFETY INSTRUCTIONS

SAVE THESE INSTRUCTIONS

INSTALLATION INSTRUCTIONS

Tools and Parts

Vent clamps

Caulking gun and

compound (for installing

new exhaust vent)

Tin snips (new vent

installations)

⁄

" nut driver or socket

wrench (recommended)

Tape measure

Do not repair or replace any part of the dryer or attempt

any servicing unless specifically recommended in this

Use and Care Guide or in published user-repair

instructions that you understand and have the skills to

carry out.

Do not use fabric softeners or products to eliminate static

unless recommended by the manufacturer of the fabric

softener or product.

Do not use heat to dry articles containing foam rubber or

similarly textured rubber-like materials.

Clean lint screen before or after each load.

Keep area around the exhaust opening and adjacent

surrounding areas free from the accumulation of lint, dust,

and dirt.

The interior of the dryer and exhaust vent should be

cleaned periodically by qualified service personnel.

See installation instructions for grounding requirements.

Parts needed

Check local codes. Check existing electrical supply and venting.

See "Electrical Requirements" and "Venting Requirements"

before purchasing parts.

For close-clearance installations between 28.65" (728 mm)

and 34.15" (867 mm), see "Plan Vent System" section for

venting requirements.

Mobile home installations require metal exhaust system hardware

available for purchase from the dealer from whom you purchased

your dryer. For further information, please refer to the "Assistance

or Service" section.

If using a power supply cord:

Use a UL listed power supply cord kit marked for use with

clothes dryers. The kit should contain:

A UL listed 30-amp power supply cord, rated

120/240 volt minimum. The cord should be type SRD or

SRDT and be at least 4 ft (1.22 m) long. The wires that

connect to the dryer must end in ring terminals or spade

terminals with upturned ends.

A UL listed strain relief.

34.15"

(867 mm)