Whirlpool WGD6400SW0 Технічний паспорт - Сторінка 10

Переглянути онлайн або завантажити pdf Технічний паспорт для Сушарка Whirlpool WGD6400SW0. Whirlpool WGD6400SW0 12 сторінок. 29" gas dryer
Також для Whirlpool WGD6400SW0: Перелік деталей (8 сторінок), Посібник із швидкого старту (6 сторінок)

Друкувати сторінку

TECH SHEET - DO NOT DISCARD

Perform the Console Buttons and

Indicators Diagnostic test, page 1

to verify repair.

Some buttons do not light

indicators:

1. Perform steps in Accessing &

Removing the Electronic Assemblies,

page 11 and visually check the user

interface assembly connections.

If visual check passes, replace the

user interface assembly.

2. Plug in dryer or reconnect power.

3. Perform the Console Buttons and

Indicators Diagnostics test, page 1 to

verify repair.

TEST #7 Door Switch

Activate the diagnostic test mode as

shown on page 1, and perform the Door

Switch Diagnostic test, page 1.

Functionality is verified with a beep each

time the door is closed and opened, and a

number and letter appears in the display

(i.e.,

If any of these conditions are not met:

Unplug dryer or disconnect power.

Check that the wires between the door

switch and machine control electronics

are connected. See figure 12 for switch

location and see Removing the Front

Panel/Drum Assembly, page 10.

If the connections are OK, replace

the door switch assembly and retest.

If the door switch assembly has

been replaced and dryer still does

not start, replace the machine

control electronics.

Door Switch

Figure 12. Door switch location.

FOR SERVICE TECHNICIAN'S USE ONLY

ADJUSTING

CUSTOMER-FOCUSED

DRYING MODES

NOTE: If the customer is complaining

about the clothes being damp and the

moisture sensor passes TEST #5, page 9,

step 3, the total dry time for an automatic

cycle can be lengthened by changing from

a "1" (standard auto cycle) to a "2" (15%

more drying time) or "3" (20% more drying

time) auto cycle.

1. Press and hold the Dryness button for

5 seconds. The dryer will beep and

display

for one second, then the

current drying mode will be seen on

the display. The factory default value

is "1".

2. To select a different drying mode, press

the Dryness button again. The dryer

display will flash and show the

available settings.

3. With the display flashing the selected

drying mode, press the Start button to

save the drying mode and exit (the

Start button in this mode does not start

a drying cycle). The result will be

stored in EEPROM of the control

board, and will be retained after a

power loss.

4. Press the Pause/Cancel button at any

time to cancel changes and exit from

this mode.

REMOVING THE FRONT

PANEL/DRUM ASSEMBLY

1. Unplug dryer or disconnect power.

2. Remove the lint screen.

3. Remove the two screws holding the lint

screen duct to the top.

4. Open the door.

5. Push on the retaining clips located

under top of dryer on the right and left

side using a flat object such as a putty

knife. See figure 13.

Door Switch

Front Cover Screw

Wire Harness

(Inside Cabinet)

Connector

Top Clips

Figure 13. Slowly rotate top backwards

and support.

6. Slowly rotate top backwards and lean

against wall, or support with a prop rod.

7. Disconnect the door switch wire

harness located on the right side. See

figure 13.

8. Remove the front panel/door assembly

by removing the two front cover screws

at the top of the panel inside the

cabinet, and lifting upward.

9. Remove the front bulkhead by

loosening the upper two screws and

removing the lower two screws. See

figure 14.

Drum Face

Plate

Figure 14. Remove the front bulkhead.

10. Lower components can be accessed

at this time, however, if the drum is to

be removed, the belt must be

removed. See TEST #3, step 4,

page 6.

Reinstalling the Front Panel/Drum

Assembly

Refer to preceding removal sections and

replace in reverse order.

PART NO. W10054160

PAGE 10

Lint Screen

Duct