Whirlpool WGD9151YW Посібник з використання та догляду - Сторінка 11
Переглянути онлайн або завантажити pdf Посібник з використання та догляду для Сушарка Whirlpool WGD9151YW. Whirlpool WGD9151YW 40 сторінок. Installation guide
Також для Whirlpool WGD9151YW: Посібник користувача (32 сторінок), Інструкція з експлуатації (8 сторінок), Посібник з монтажу (36 сторінок)
Друкувати сторінку
5.
Adjust cycle settings, if desired
Sensing
Steam model shown
You may adjust different settings, depending on whether
you have selected an Auto Cycle, Manual Cycle, or Steam
Cycle (on some models). See the "Cycle Guide" for detailed
information.
NOTE: Not all options and settings are available with all cycles.
Not all cycles are on all models.
Auto Cycles:
You can select a different dryness level, depending on your
load, by pressing the button for More, Normal, or Less.
Selecting More, Normal, or Less automatically adjusts the
dryness level at which the dryer will shut off. Once a dryness
level is set, it cannot be changed without stopping the cycle.
Automatic cycles give the best drying in the shortest time.
Drying time varies based on fabric type, load size, and
dryness setting.
Manual Cycles:
When you select a Manual Cycle, the
default time appears in the display.
Use the More Time s and Less Time t
buttons to increase or decrease the time
in 1 minute increments. Press and hold to
change the time in 5 minute increments.
The default temperature may be changed by pressing the
Temperature button until the desired dry temperature is lit.
You may also adjust the time or temperature on a manual cycle
at any time while the cycle is running.
Steam Cycles (on some models):
Steam cycles add an extra boost of steam to help reduce
odors and loosen wrinkles.
Quick Refresh: Use to reduce odors and light wrinkles from
small loads of 3-4 items.
Enhanced Touch Up: Use to reduce wrinkles, including from
loads left in the dryer too long.
6.
Press and hold START/PAUSE
to begin cycle
Press and hold the START/PAUSE button to begin the cycle.
Steam
Control Lock
Wet
Damp
Done
Cool
Wrinkle
Down
Shield
Sensing
7.
Remove garments promptly
after cycle is finished
Steam model shown
Promptly remove garments after cycle has
completed to reduce wrinkling. If you will be
unable to remove the load promptly, select the
Wrinkle Shield option before pressing START/PAUSE
to add up to 90 minutes of periodic tumbling after the
end of the drying cycle.
Changing the Auto Cycle settings
to increase drying time
If all your loads on all Auto Cycles are consistently
not as dry as you would like, you may change the default
settings to increase the default dryness level.
Your automatic drying settings can be adjusted to adapt to
different installations, environmental conditions or personal
preference. This change is retained and will affect all of your
Automatic cycles, not just the current cycle/load. There
are 3 drying settings, which are displayed using the time
display:
1 Factory preset dryness level.
2 Slightly drier clothes, 15% more drying time.
Wet
Damp
3 Much drier clothes, 30% more drying time.
To change the drying settings:
NOTE: The settings cannot be changed while the dryer is
running or paused. The dryer must be in standby mode (the
power button is off or only the DONE indicator lit) to adjust
the default settings.
1. Before starting a cycle, press and hold the TEMP button
for 6 seconds.
2. Press the TEMP button to select the dryness level
shown in the time display: 1, 2, or 3.
3. Press START/PAUSE to save the new dryness level
setting.
Steam
Control Lock
Sensing
Wet
Damp
Cool
Done
Wrinkle
Down
Shield
11