Whirlpool YWED9600TZ0 Посібник з використання та догляду - Сторінка 10
Переглянути онлайн або завантажити pdf Посібник з використання та догляду для Сушарка Whirlpool YWED9600TZ0. Whirlpool YWED9600TZ0 48 сторінок. Electronic electric dryer
Друкувати сторінку
Vent s ystem chart
NOTE: Side andbottom exhaust installations
have a90 ° turn
inside thedryer. Todetermine maximum e xhaust length, add one
90 °turn tothechart,
Number of Type of
Boxor
Angled
g0 °turns
vent
Iouvered
hoods
or elbows
hoods
0
Rigid metal
64ft (20m)
58ft (17.7 m)
Flexible m etal 36ft (11m)
28ft (8,5 m)
1
Rigid metal
54ft (16.5 m) 48ft (14,6 m)
Flexible m etal 31ft (9,4 m)
23ft (7m)
2
Rigid metal
44ft (13,4 m) 38ft (11,6 m)
Flexible m etal 27ft (8,2 m)
19ft (5.8 m)
3
Rigid metal
35ft (10.7 m) 29ft (8.8 m)
Flexible m etal 25ft (7,6 m)
17ft (5.2 m)
4
Rigid metal
27ft (8,2 m)
21ft (6.4 m)
Flexible m etal 23ft (7m)
15ft (4.6 m)
4. Screw thelegs intothelegholes byhand. U se awrench t o
finish turning t helegs until t hediamond marking i snolonger
visible.
5. Place acarton corner p ost f rom dryer p ackaging under e ach
ofthe2 dryer b ack corners. Stand thedryer u p.Slide the
dryer o nthecorner p osts until i tisclose toitsfinal l ocation.
Leave e nough r oom toconnect theexhaust vent.
1. Using a 4"(10.2 cm) c lamp, connect vent t oexhaust outlet i n
dryer. Ifconnecting toexisting v ent, m ake sure thevent i s
clean. The dryer v ent m ust f itover t hedryer e xhaust outlet
andinside theexhaust hood. Check t hatthevent i ssecured
toexhaust hood witha4"(10.2 cm) c lamp.
2. Move dryer i ntoitsfinal l ocation. Donotcrush orkink vent.
3. (On gas models) Check that there are no kinks in the flexible
gas line.
4. Once the exhaust vent connection is made, remove the
corner posts and cardboard.
1. Install exhaust hood. Use caulking compound to seal exterior
wall opening around exhaust hood.
2. Connect vent to exhaust hood. Vent must fit inside exhaust
hood. Secure vent to exhaust hood with 4" (10.2 cm) clamp.
3. Run vent to dryer location. Use the straightest path possible.
See "Determine vent path" in "Plan Vent System." Avoid 90 °
turns. Use clamps to seal all joints. Do not use duct tape,
screws or other fastening devices that extend into the interior
of the vent to secure vent.
Excessive Weight Hazard
Use two or more people to move and install dryer.
Failure to do so can result in back or other injury.
1. To protect the floor, use a large flat piece of cardboard from
the dryer carton. Place cardboard under the entire back edge
of the dryer.
2. Firmly grasp the body of the dryer (not the console panel).
Gently lay the dryer on the cardboard.
See illustration.
The dryer must be connected to the cold water faucet using the
new inlet hoses. Do not use old hoses.
1. Turn cold water faucet off and remove washer inlet hose.
2. Remove old rubber washer from inlet hose and replace with
new rubber washer provided. If space permits, attach the
brass female end of the "Y" connector to the cold water
faucet.
NOTE: If "Y" connector can be attached directly to cold water
faucet, go to Step 6. If "Y" connector cannot be attached
directly to the cold water faucet, the short hose must be
used. Continue with Step 3.
3. Attach short hose to cold water faucet. Screw on coupling by
hand until it is seated on faucet.
4. Using pliers, tighten the couplings with an additional two-
thirds turn.
NOTE: Do not overtighten.
Damage to the coupling can
result.
5. Attach "Y" connector to brass male end of small hose. Screw
on coupling by hand until it is seated on connector.
6. Attach straight end of long hose to "Y" connector.
7. Attach washer cold inlet hose to other end of "Y" connector.
Screw on coupling by hand until it is seated on connector.
3.
Examine the leveling legs. Find the diamond marking.
10