Whirlpool 36'' Freestanding Gas Range Інструкція з монтажу - Сторінка 2

Друкувати сторінку

Whirlpool 36'' Freestanding Gas Range Інструкція з монтажу

Before you start...

Your safety and the safety

of others is very important.

We have provided many important safety

messages in this manual and on your

appliance. Always read and obey all safety

messages.

This is the safety alert symbol. This

symbol alerts you to hazards that can

kill or hurt you and others. All safety

messages will be preceded by the safety alert

symbol and the word "DANGER" or

"WARNING". These words mean:

DANGER

You will be killed or seriously injured if

you don't follow instructions.

WARNING

You can be killed or seriously injured if

you don't follow instructions.

All safety messages will identify the hazard,

tell you how to reduce the chance of injury,

and tell you what can happen if the

instructions are not followed.

Important: Observe all governing codes and

ordinances. Failure to meet codes and

ordinances could lead to fire or electrical shock.

Proper installation is your responsibility. A

qualified technician must install this range. Make

sure you have everything necessary for correct

installation. It is the installer's responsibility to

comply with installation clearances specified on

the model/serial rating plate. The model/serial

rating plate is located on the oven frame behind

the storage drawer panel.

Check location where range will be installed.

The range should be located for convenient use

in kitchen.

When installing a range under existing cabinets

and the installation does not meet the minimum

cabinet clearances, install a range hood above

the cooktop to avoid burn hazards.

ALL OPENINGS IN THE WALL OR FLOOR

WHERE RANGE IS TO BE INSTALLED MUST

BE SEALED.

Cabinet opening dimensions that are shown

must be used. Given dimensions are minimum

clearances.

Grounded electrical supply is required. See

"Electrical requirements," Panel A and B.

It is the customer's responsibility:

To contact a qualified electrical installer.

To assure that the electrical installation is

adequate and in conformance with National

Electrical Code, ANSI/NFPA 70 — latest edition*

and all local codes and ordinances.

Mobile home installation

The installation of this range must conform with

the Manufactured Home Construction and

Safety Standard, Title 24 CFR, Part 3280

[formerly the Federal Standard for Mobile Home

Construction and Safety, Title 24, HUD (Part

280)] or, when such standard is not applicable,

the Standard for Manufactured Home

Installations, ANSI A225.1/NFPA 501A*, or with

local codes.

When this range is installed in a mobile home, it

must be secured to the floor during transit. Any

method of securing the range is adequate as

long as it conforms to the standards listed

above.

Four-wire power supply cord or cable must be

used in a mobile home installation. The

appliance wiring will need to be revised. See

"Four-wire electrical connection," Panel B.

Copies of the standards listed above may be obtained from:

* National Fire Protection Association

One Batterymarch Park

Quincy, Massachusetts 02269

Panel A

Cabinet opening and product dimensions

Cabinet opening dimensions shown are for:

25" countertop depth, 24" base cabinet depth, 36" countertop height

13" max.

upper cabinet depth

30" min. cabinet

opening width

18" upper

cabinet to

countertop

30-3/8"

opening width

4" min.

wall receptacle or

clearance from

junction box –

both sides of

8" to 22" from

range to side

either cabinet,

wall or other

7" max. from floor.

combustible

material above

the countertop.

7/8" min.

required

between

cutout and

cabinet door

or hinge.

** Note: 24" min. when bottom of wood or metal cabinet

is protected by not less than 1/4" flame retardant

millboard covered with not less than No. 28 MSG

sheet steel, 0.015 stainless steel, 0.024" aluminum or

0.020" copper.

30" min. clearance between the top of the cooking

platform and the bottom of an unprotected wood or

metal cabinet.

Important: Observe all governing codes and

ordinances.

Grounded electrical outlet is required. See

"Electrical requirements," Panel A and B.

Cabinet opening dimensions that are shown

must be used.

Do Not pinch the power supply cord between

the range and the wall.

Do Not seal range to side cabinets.

Tools needed:

level

flat-blade

screwdriver

3/8" drive

ratchet

measuring

tape or ruler

Electrical requirements

If codes permit and a separate ground wire is

used, it is recommended that a qualified

electrician determine that the ground path and

wire gauge are in accordance with local codes.

Do Not ground to a gas pipe.

Check with a qualified electrician if you are not

sure range is properly grounded.

Do Not have a fuse in the neutral or ground

circuit.

Recommended ground method

It is the personal responsiblity and

obligationof the customer to contact a qualified

electrician to assure that the electrical

installation is adequate and is in conformance

with the National Electrical Code, ANSI/NFPA 70

— latest edition*, and all local codes and

ordinances.

Power supply cord is not supplied, but is

available from your dealer or local electrical

supply house.

For minimum

clearance to

the top of

the cooktop,

see Note.

26-3/8"

depth

with

handle

24-1/2"

Parts supplied:

floor-mounted

anti-tip bracket

Brackets must be securely mounted to sub-floor.

Thickness of flooring may require longer screws to

anchor bracket to sub-floor. Longer screws are

available from your local hardware store.

hand or

electric drill

3/8" and 5/16"

nut driver

safety

glasses

Range must be connected to the proper

electrical voltage and frequency as specified on

the model/serial rating plate. (The model/serial

rating plate is located on the oven frame behind

the storage drawer panel.)

THE RANGE MUST BE CONNECTED

WITH COPPER WIRE ONLY.

A four-wire or three-wire, single-phase,

120/240-volt, 60- Hz, AC-only, electrical supply

(or four-wire or three-wire 120/208-volt if

specified on the model/serial rating plate) is

required on a separate, 40-ampere circuit, fused

on both sides of the line.

A time-delay fuse or circuit breaker is

recommended.

36"

cooktop

height

30" width

2 plastic anchors

2 screws (#10 x 1-1/2")

Not shown:

literature pack

wood floors:

1/8" drill bit

concrete/ceramic floors:

3/16" carbide-tipped

masonry drill bit (Hammer

may be needed for

anchors.)

channel lock

pliers

gloves

46-13/16"

overall

height