Whirlpool GZ9736XSSDISC Інструкція з монтажу та інструкція з експлуатації та догляду - Сторінка 4

Переглянути онлайн або завантажити pdf Інструкція з монтажу та інструкція з експлуатації та догляду для Вентиляційна витяжка Whirlpool GZ9736XSSDISC. Whirlpool GZ9736XSSDISC 32 сторінки. 30" (76.2 cm) and 36” (91.4 cm) wall-mount canopy range hood

Друкувати сторінку

Tools and Parts

Gather the required tools and parts before starting installation.

Read and follow the instructions provided with any tools listed

here.

Tools needed

■

Level

■

Drill

⁵⁄₁₆" (8 mm) drill bits for pilot holes

■

⁵⁄₃₂" (4 mm) drill bits

■

Pencil

■

Tape measure or ruler

■

Caulking gun and weatherproof caulking compound

■

Phillips screwdriver

■

Vent clamps

■

Metal snips

For vented installations, you will also need:

■

1 wall or roof cap

■

Metal vent system

For non-vented (recirculation) installations, you will also

need:

■

Charcoal Filter Kit Part Number 8212566

See "Assistance or Service" section to order.

■

5" (12.7 cm) diameter expandable/flexible aluminum duct

■

Vent clamps for a 6" (15.2 cm) diameter duct

Parts supplied

Remove parts from packages. Check that all parts are included.

■

Literature package

■

Decorative flue assembly

■

2 metal grease filters for 30" (76.2 cm) models

3 metal grease filters for 36" (91.4 cm) models

■

Parts bag containing:

■

Damper

■

Mounting bracket

■

Flue mounting bracket

■

8 drywall anchors

■

8 - 4.8 x 38 mm pan head mounting screws

■

6 - 3.9 x 9.5 mm pan head screws

■

2 - 3.9 x 5.7 mm flat head screws

INSTALLATION REQUIREMENTS

Location Requirements

IMPORTANT: Observe all governing codes and ordinances.

It is the installer's responsibility to comply with installation

clearances specified on the model/serial rating plate. The model/

serial rating plate is located behind the left filter on the rear wall of

the vent hood.

Canopy hood location should be away from strong draft areas,

such as windows, doors and strong heating vents.

Cabinet opening dimensions that are shown must be used. Given

dimensions provide minimum clearance. Consult the cooktop/

range manufacturer installation instructions before making any

cutouts.

Grounded electrical outlet is required. See "Electrical

Requirements" section.

The canopy hood is factory set for venting through the roof or

wall. For non-vented (recirculating) Installation see "Non-vented

(recirculating) Installations" in "Prepare Location" section.

Charcoal Filter Kit Part Number 4393848 is available from your

dealer or an authorized parts distributor.

All openings in ceiling and wall where canopy hood will be

installed must be sealed.

For Mobile Home Installations

The installation of this range hood must conform to the

Manufactured Home Construction Safety Standards, Title 24

CFR, Part 328 (formerly the Federal Standard for Mobile Home

Construction and Safety, Title 24, HUD, Part 280) or when such

standard is not applicable, the standard for Manufactured Home

Installation 1982 (Manufactured Home Sites, Communities and

Setups) ANSI A225.1/NFPA 501A*, or latest edition, or with local

codes.

Product Dimensions

8¹⁵⁄₁₆"

10¹⁵⁄₁₆"

(25.2 cm)

(27.8 cm)

30" (76.2 cm)

36" (91.4 cm)

7⁷⁄₈"

(20 cm)

32"

(81.3 cm) min.

46¹⁄₈"

(117.2 cm) max.

19¹⁄₁₆"

(48.4 cm)

5¹⁄₁₆"

(12.9 cm)

19⁵⁄₈"

(49.8 cm)