Whirlpool RANGE HOOD UXT2036AY Інструкція з монтажу та інструкція з експлуатації та догляду - Сторінка 7
Переглянути онлайн або завантажити pdf Інструкція з монтажу та інструкція з експлуатації та догляду для Вентиляційна витяжка Whirlpool RANGE HOOD UXT2036AY. Whirlpool RANGE HOOD UXT2036AY 28 сторінок. 30" (76.2 cm) and 36" (91.4 cm)
Також для Whirlpool RANGE HOOD UXT2036AY: Інструкція з монтажу та інструкція з експлуатації та догляду (36 сторінок), Інструкція з монтажу та інструкція з експлуатації та догляду (28 сторінок)
Друкувати сторінку
INSTALLATION INSTRUCTIONS
NOTE: It is recommended
that the vent system be installed
before hood is installed.
Before making cutouts, make sure there is proper clearance
within the ceiling or wall for exhaust vent.
1. Disconnect
power.
2. Depending on your model, determine which venting method
to use: roof or wall.
3. Select a flat surface for assembling the range hood. Place
covering over that surface.
4. Lift the range hood and set it upside down onto covered
surface.
5. If cabinet has recessed bottom, add wood filler strips on each
side. Install screws to attach filler strips in locations shown.
Wood filler strips
(recessed
cabinet
bottoms
onJy)
To wire through top:
1. Mark a line distance "A" from the right of the centerline on the
underside of the cabinet. Mark the point on this line that is
7/8"(2.2 cm) from back wall. Drill a 1W' (3.2 cm) diameter hole
through the cabinet at this point.
I
A
i I
\
%" (2.2 cm)
from wall,
not cabinet
frame
A. 8%" (21.3 cm) for30"
(76.2 cm) models
11%" (28.9 cm) for36"
(91.4 cm) models
-_\
\
\
\
\ \
\
\
X/\
\
\
\ \
\
\
\ \
\
\ \
/
3" (7.6 cm)
Wall
Determine Wiring Hole Location
Cut only one 1V4"(3.2 cm) diameter wiring access hole. See
Step 2 for wiring hole location instructions.
1. Determine and clearly mark a vertical centerline on the wall
and cabinet in the area the vent opening will be made.
I
]
I
A. Centerline
To wire through wall:
1. Mark a line distance "A" from the right of the centerline on the
underside of the wall. Mark the point on this line that
is 7/8"(2.2 cm) from the underside of the cabinet. Drill a
1V4" (3.2 cm) diameter hole through the rear wall at this point.
L
I
i
•
i_< ...........................
_
Y?'(2.2 cm)
i
i
i
CenterJine
A. 8%" (21.3
cm) for30"
(76.2
cm) models
11%"
(28.9
cm) for36"
(91.4
cm) models
Cut Openings for 7" (17.8 cm) Round Vent
To make a circular vent openings on the underside of the
cabinet top and bottom:
1. Mark a centerline on the underside of the top of cabinet.
2. Mark a line 5" (12.7 cm) from the back wall on the underside
of the top and bottom of cabinet.
3. Use a compass or a circle template to draw a circle with a
diameter that is W' (0.64 cm) larger than the vent.