Whirlpool RGH 8300-2 Інструкція з монтажу та експлуатації

Переглянути онлайн або завантажити pdf Інструкція з монтажу та експлуатації для Вентиляційна витяжка Whirlpool RGH 8300-2. Whirlpool RGH 8300-2 4 сторінки. Vented range hood

Друкувати сторінку

RGH 8300-l

. .

RGHt!S3m-25

INSTALL

RANGE

HOOD

This

unit

can

be vented

vertically

through

uoper

cabine!s

horrzontally

through

an outside

wall. A typical

vertical

installet~on

shown in Figure 1. A ryolcal

horizonial

rnstallatron

IS shown In Figure

2. For proper ventila:ron

when used wrth an indoor

electrrc

grill. see

paoe 2 for gurctelines

for proper

auct sizing. Improper

duct sizing or

ins:alletion

of restrictive

roof jacks can reduce

air moving

capacity

and provide

inadequate

ventilation

for an indoor

electric

grill. For

mcst

efficient

smoke

removal,

the

top of the hood

should

approximately

56 Inches (13T.6 cm) from the floor.

1. Make a template

or transfer

measurements

shown

in Fig. 3 to

cabinets

or wall.

2. Cut holes to accomodate

ventilating

duct allowing

'4" (-6 cm)

clearance

on all 4 srdes for back vent. Allow !." (1.9 cm) clearance

toward front for vertical

vent. A!low I%" (.6 cm) on other3 sides for top

vent.

3. Cut appropriate

hole for electrical

wiring.

4. Run

wire

through

wall

or cabinets

according

to Nattonal

Electrical

Code and applrcable

local codes. (DO NOT turn power on

until installation

is complete.)

For an easrer

rnstallaiion.

remove

the filters

and the three

assembltes

shown

in Frg. 4. Thus reduces

the weight

about 40%. The

blower cover and light frame assembly

are held into place with thumb

screws.

To romove

the blower

assembly,

first unplug

the blower

power supply

cord f:om the junction

box. Remove the packing

screw

from the b!ower

retarnrno

rod. then pull the blower

retalntng

rod to

one side. freeing

it from between

the bumps on the blower

housing.

6. Remove

screw holding

junction

box cover.

7. Remove

proper

electrical

knockout,

See Figure 3.

8. Remove

proper

venting

knockout.

See Figure

3. NOTE:

horizonta!

discharge

is selected

an additronal

knockout

in the blower

cradle must be removed.

9. Attach !he damoer

as shown

in Figure 5 for vertical

discharge

Fig. 6 for horizontal

discharge.

10. Lift the hood into position.

Mark location

of four mounting

holes.

11. Remove hood and start all four screws in center of narrow neck of

keyhole

slot marked

on cabmet

bottom.

72. Lift the hood into posrrion

simultaneously

feeding

the electrical

wire through

the knockout.

Fojlow

aoplicable

local codes

and/or

latest Nattonal

Electrrcal

Code for electrical

connector

to be used at

field wiring

entrance.

13. Tighten

screws to secure

hood. Be sure screw head is in narrow

neck of keyhole

slot.

14. Install proper

duct work. See page 2.

16. COmplete

electrical

wiring

-in junction

box according

to the

National

Electrical

Code and applicable

Local Codes.

NOTE:

This

Unit must be permanently

grounded

in accordance

with the National

Electrical

Code and applrcable

Local codes.

16. Replace

junction

box cover,

17. Replace

blower.

See page 3 for proper

blower

orientation

18. Replace

blower

cover.

light frame assembly

and filters.

NOTE: It has been found that a large part of the energy

loss of the

average

home

IS due to outslde

air InfIltratIng

the structure,

Sea)

around

duc!work

wncre

It passes

through

outside

walls or ceilrng.

Sea-l around

electrical

wrrrng also.

FIGURE

L V,lPil,G -,:.r,:*=w;

,-LIGHT

FRAME

,/-9LOWER

RETAINING

ROD

J'JYCTION

90x

COVER

-BLOWER CRADLE

FIGURE