Whirlpool RJH 3330-1 Посібник з монтажу та експлуатації - Сторінка 5
Переглянути онлайн або завантажити pdf Посібник з монтажу та експлуатації для Вентиляційна витяжка Whirlpool RJH 3330-1. Whirlpool RJH 3330-1 6 сторінок. Whirlpool microshelf hood installation and operating instructions rjh 3330-1
Друкувати сторінку
Place the microwave
oven on the hood shelf on the
right hand side of the hood aligning
the front and
right
hand side of the microwave
oven with the
front and right hand side of the Microshelf
Hood.
Use the leveling
bolts provided
to level shelf hood
after weight of the appliance
is placed on it. Bolts
are provided
in the installation
package. Screw the
bolts into the nuts provided
on the lower left and
right hand sides of the shelf hood until the unit is
level. See Figure 10.
NOTE:
The leveling
bolts have a g/16" hex head.
CAUTION:
THE MICROWAVE
OVEN MUST BE
LEVEL FROM FRONT
TO BACK TO MINIMIZE
UTENSILS
FROM
SLIDING
FORWARD
WHEN
OPENING
THE DOOR.
5.
Mark the safety bracket hole on the back wall
through
the center
of the slotted
hole
in the
bracket, so it can be attached
to the rear wall.
WARNING:
THE WEIGHT OF THE MICROWAVE
MAY
EXCEED
YOUR
LIFT:NG
ABILITY.
WE
RECOMMEND
ASSISTANCE.
6.
Remove the microwave
oven and drill a 3/16
dia. hole through
the back wall in the location
marked
in step 5 above. If a solid wood stud is
behind the wall covering,
a l/4" dia. lag bolt will be
used to mount the safety bracket to the wall. If no
solid stud is found in this location,
drill a 7/16 inch
dia. hole
in the wall
and insert
a hollow
wall
expanding
anchor
bolt.
7.
WARNING:
THE
WEIGHT
OF
THE
MICROWAVE
MAY
EXCEED
YOUR
LIFTING
ABILITY.
WE RECOMMEND
ASSISTANCE.
Place the microwave
oven on the hood shelf on the
left hand side. Plug the microwave
oven into the
outlet provided
in the top of the shelf hood.
Slide the microwave
oven to the right so the right
hand side of the microwave
oven is aligned
with
the right hand side of the hood shelf. Install the
safety bracket using the safety bracket
retaining
screw.
Before
operating
the microwave
oven,
make sure the oven cavity
and magnetron
area
cooling
vents will not be restricted.
8.
Insert
Glass
Frame Assembly
according
to
Figure 11.
Figure 11
OPERATION
AND CARE OF UNIT
CARE OF FILTERS:
LIGHTS:
A.
ALUMINUM
FILER:
For greatest efficiency,
Select
two light
bulbs
up to 60 watts
each to
the permanent
type
aluminum
filter
should
be
achieve
desired
lighting
for cooking.
The three
removed and cleaned
periodically.
position
switch
provides
two levels of lighting.
TO CLEAN:
The filter should
be soaked in hot
water and detergent,
then thoroughly
rinsed. The
aluminum
filter can be cleaned
in a dishwasher.
CARE OF EXTERIOR
SURFACES:
Clean with a mild detergent
to preserve finish. DO
NOT use abrasive cleaners.
CAUTION:
Operate the hood only with the filter
in place to prevent grease build up inside the hood.
Replacement
filters
and
repair
parts
may
be
obtained
from
Whirlpool
Corporation,
Parts
Distribution
Center, LaPorte,
Indiana
46350.
Page 5