AER COMPACT 60 2 Посібник з експлуатації - Сторінка 3
Переглянути онлайн або завантажити pdf Посібник з експлуатації для Підсилювач музичних інструментів AER COMPACT 60 2. AER COMPACT 60 2 8 сторінок. Amplifier
Також для AER COMPACT 60 2: Посібник користувача (10 сторінок)
Друкувати сторінку
2. Safety Precautions
The following guidelines shall help minimize the risk of injury through
fire or electric shock.
1. Carefully read these safety notes before you use the device!
2. Keep these safety notes in a safe place.
3. Pay attention to all warnings, instructions and additional texts on
the unit.
4. Do not install or use your amp in close proximity to water or if you
are wet yourself.
5. Use your amp in a safe place where nobody can step on cables or
trip over and damage them.
6. Pay attention to an unhindered air circulation around the amp, ne-
ver obstruct the air vents or grilles.
7. Always pull the mains plug before cleaning your amp. Use only a
dry cloth for cleaning. Avoid the use of detergents and do not let
any liquids seep into the unit.
3. Controls and Connections
Front panel top
(from left to right):
clip
high
low
gain
input
C C ompact 60
channel 1
input
6.3 mm stereo jack socket
high/low
Input sensitivity selector switch
pressed = lower sensitivity
clip
This indicator lights up when overload is imminent in
the respective channel.
gain
Input level control
colour
This switch activates the midrange contour filter.
Boosts presence and slightly cuts midrange
frequencies.
bass
Bass control
middle
Midrange control
treble
Treble control
channel 1
colour
bass
middle
treble
2
8. Use only the right fuses with the same current rating and trigger
characteristic as replacements. Never mend fuses! Pull the mains
plug before replacing a fuse. Should a fuse blow again after a
short while, the device needs to be checked.
9. Never install your amp close to devices with strong elec-
tromagnetic fields such as large mains transformers, revolving
machines, neon illumination etc. Do not lay signal cables parallel
to power current cables.
10. There are no user-servicable components inside the unit. To avo-
id the risk of an electric shock, the unit must not be opened. All
maintenance, adjustment and repair works should be carried out
by qualified staff only. Any unauthorized tampering will void the
2-year warranty.
11. In keeping with the EMV regulations screened cables with cor-
rectly fitted connectors must be used for all signal connections.
12. Always use an earthed power supply with the correct mains volta-
ge. If you are in doubt about the power outlet's ground, have it
checked by a qualified technician.
13. Cable up your amp only when it is powered off.
channel 2
input
clip
line
mic
gain
bass
channel 2
input
XLR/6.3 mm jack plug combi socket
line/mic
Signal source selector switch.
line: For instruments (pickups), only via jack plug.
mic: For microphones with a jack or an
XLR connector.
clip
This indicator lights up when overload is imminent in
the respective channel.
gain
Input level control
bass
Bass control
treble
Treble control
eff. pan
panorama control to distribute the effects between
the channels.
left: internal effect on channel 1 & external
effect on channel 2
mid: internal & external effect on channel 1
and channel 2
right: internal effect on channel 2 & external
effect on channel 1
select
push button for selection of four effects, indicated by
the LEDs between return and master.
return
level control for the internal effects
power
This LED indicates that your amplifier is ready to use
master
Adjusts the overall volume level
select
power
eff. pan
return
treble
effect
master
3