Direct Healthcare Group Dyna-Form Mercury Advance Посібник користувача - Сторінка 9
Переглянути онлайн або завантажити pdf Посібник користувача для Медичне обладнання Direct Healthcare Group Dyna-Form Mercury Advance. Direct Healthcare Group Dyna-Form Mercury Advance 16 сторінок.
Також для Direct Healthcare Group Dyna-Form Mercury Advance: Посібник користувача (9 сторінок)
Друкувати сторінку
7.4 Alternating Mode Failure (no alternation)
This will be indicated by a warning LED on A and B and an audible warning.
1. Reset the warning – turn off Power and press the audible warning mute button.
2. Disconnect the air hoses to reduce pressure – reconnect when pressure has decreased.
7.5 Initialising Failure
This will be indicated by a warning LED on A, B and C and an audible warning.
1. Press the audible warning mute button to silence the
2. Check the power cable is firmly plugged into the mains outlet and the Control Unit;
and check the mains power is switched on.
3. Check the Control Unit fuse (1 AMP) – fuses can be released using a screwdriver
to push and turn.
8. Maintenance Procedures
8.1 Safety Warning
Only qualified technicians trained or formally approved by Direct
Healthcare Group Ltd. in the operation and maintenance of
Direct Healthcare Group products may carry out maintenance,
modification or repair work on the equipment. Unqualified
personnel attempting to work on Direct Healthcare Group Power
Units risk serious injury to themselves and others and possibly
death by electrocution. Inlet fuse NOT to be replaced by operator
or patient, to be replaced by service personnel only.
Warning – Do not modify this equipment without
authorisation of Direct Healthcare Group.
8.1.1 Servicing
A service light will illuminate when a service is due.
Direct Healthcare Group (DHG) recommend that the Power
Unit (Pump) should be serviced every 8760 hours of operation (one
continuous year running). The unit contains no user serviceable
parts and should only be carried out by persons as described in
section 8. 1 . DHG will make available on request service manuals,
component parts lists and other information necessary for any
suitably qualified person (As in 8. 1 ) to carry out repair or service
the system. For Service, maintenance and any questions regarding
this please contact DHG.
8.2 Cleaning Procedures
Warning: Before cleaning the System make sure that the Power
Unit (Pump) is disconnected from the mains electricity supply.
Do not immerse the Power Unit (Pump) in water or other fluids.
Do not autoclave, nor use phenol for cleaning.
Do wash hands before commencing the cleaning process.
Wear appropriate protective clothing such as gloves, apron
and a mask.
Ensure all work surfaces are cleaned before and after contact
with the Mattress.
U S E R M A N U A L
.
audible warning
8.3 Warning – Cleaning the Mattress
1. Cleaning should take place after use or between patients.
2. With cover left on the Mattress disconnect the Mattress from
the Power Unit (Pump).
3. Clean the surface of the wash down table with Hypochlorite
solution or equivalent disinfectant.
4. Wash Mattress top using hot water (60 degrees C) containing
detergent – dry with a paper towel.
5. Use a Hypochlorite solution 1,000 parts per million available
chlorine. For heavy contamination use a Hypochlorite solution
10,000 parts per million available chlorine. Please ensure
thorough rinsing after cleaning.
6. Using suitable brush, hot water, detergent or Hypochlorite
solution, clean Umbilical Hose and CPR Valve. Dry with
paper towel.
7. If required, the Mattress Cover may be removed and
machine-washed at a temperature of 80 degrees C, for not
less than 10 minutes. The individual Air Cells can be wiped
down with established disinfectants.
8. To avoid shrinkage of the cover line dry in an indoor clean
environment or tumble dry on a low heat setting not
exceeding 40 degrees C and not for longer than 10 minutes.
Covers must be thoroughly dried before re-fitting to the
mattress.
8.4 Warning – Cleaning the Power Unit (Pump)
The Power Unit can be cleaned by wiping with a cloth dampened
with a detergent solution or Hypochlorite solution.
Also refer to symbol chart.
8.4.1 Warning
Ensure the Mercury Advance System is not exposed to:
1. Excessive heat sources e.g. fires, radiators etc.
2. Water, particularly immersion of the pump.
D I R E C T H E A L T H C A R E G R O U P . C O M
9