Direct Healthcare Group Dyna-Form Mercury Advance Посібник користувача - Сторінка 6
Переглянути онлайн або завантажити pdf Посібник користувача для Медичне обладнання Direct Healthcare Group Dyna-Form Mercury Advance. Direct Healthcare Group Dyna-Form Mercury Advance 9 сторінок.
Також для Direct Healthcare Group Dyna-Form Mercury Advance: Посібник користувача (16 сторінок)
Друкувати сторінку
D Y N A - F O R M M E R C U R Y A D V A N C E
8.3 Warning – Cleaning the Mattress
1. Cleaning should take place before and after use, and between patients.
2. With cover left on the Mattress disconnect the Mattress from the Control Unit.
3. Clean the surface of the wash down table with Hypochlorite solution or equivalent disinfectant.
4. Wash Mattress top using hot water (60 degrees C) containing detergent – dry with a paper towel.
5. Use a Hypochlorite solution 1,000 parts per million available chlorine. For heavy contamination use a Hypochlorite solution 10,000
parts per million available chlorine. Please ensure thorough rinsing after cleaning.
6. Using suitable brush, hot water, detergent or Hypochlorite solution, clean Umbilical Hose and CPR Valve. Dry with
paper towel.
7. If required, the Mattress Cover may be removed and machine-washed at a temperature of 80 degrees C, for not less than 10
minutes. The individual Air Cells can be wiped down with established disinfectants.
8. To avoid shrinkage of the coverline dry in an indoor clean environment or tumble dry on a low heat setting not exceeding 40
degrees C and not for longer than 10 minutes. Covers must be thoroughly dried before re-fitting to the mattress.
8.4 Warning – Cleaning the Control Unit
The Control Unit can be cleaned by wiping with a cloth dampened with a detergent solution or Hypochlorite solution.
Also, refer to symbol chart.
8.4.1 Warning
Ensure the Mercury Advance System is not exposed to:
1. Excessive heat sources e.g. fires, radiators etc.
2. Water, particularly immersion of the Control Unit.
9. Technical Specification
Declaration – Electromagnetic Emissions – for all ME EQUIPMENT and ME SYSTEMS
Guidance and Manufacturer's Declaration – Electromagnetic Emission
The MAT1210001 is intended for use in the electromagnetic environment specified below.
The customer or the user of the system should ensure that it is used in such an environment.
Emission Test
Compliance
RF emissions
Group 1
CISPR 11
RF emission
Class B
CISPR 11
Harmonic emissions
Class A
IEC 61000-3-2
Voltage fluctuations/flicker
Complies
emissions
IEC 61000-3-3
1 0
D I R E C T H E A L T H C A R E G R O U P . C O M
Electromagnetic Environment – Guidance
The system uses RF energy only for its internal function.
Therefore, its RF emissions are very low and are not likely
to cause any interference in nearby electronic equipment.
The system is suitable for use in all establishments, including
domestic establishments and those directly connected to
the public low-voltage power supply network that supplies
buildings used for domestic purposes.
U S E R M A N U A L
9. Technical Specification
Declaration – Electromagnetic Immunity
Guidance and Manufacturer's Declaration – Electromagnetic Emission
The MAT1210001 is intended for use in the electromagnetic environment specified below.
The customer or the user of the system should ensure that it is used in such an environment.
Immunity Test
IEC 60601
Test Level
Electrostatic discharge (ESD)
±6 kV contact
IEC 61000-4-2
±8 kV air
Electrical fast transient/burst
±2 kV for power
IEC 61000-4-4
supply lines
±1 kV for input/output line(s)
Surge Immunity Test
± 1 kV line(s) to line(s)
IEC 61000-4-5
Voltage dips, short
Voltage Dips
Period
interruptions and voltage
%U
(Cycles)
T
variations on power supply
30
25
input lines
60
5
IEC 61000-4-11
>95
0.5
Voltage
Seconds
Interruption
% U
T
>95
5
Power frequency (50Hz)
3 A/m
3 A/m
magnetic field
IEC 61000-4-8
NOTE U
is the a.c. mains voltage prior to application of the test level.
T
D I R E C T H E A L T H C A R E G R O U P . C O M
Compliance Level
Electromagnetic
Environment – Guidance
±6 kV contact
Floors should be wood,
concrete or ceramic tile.
±8 kV air
If floor are covered with
synthetic material, the relative
humidity should be at least
30%.
±2 kV for power
Mains power quality
should be that of a typical
supply lines
commercial or hospital
±1 kV for input/output line(s)
environment.
±1 kV differential mode
Mains power quality
should be that of a typical
commercial or hospital
environment.
Voltage Dips
Period
Mains power quality
%U
(Cycles)
should be that of a typical
T
commercial or hospital
30
25
environment. If the user of
60
5
the Span system requires
continued operation during
>95
0.5
power mains interruptions,
it is recommended that the
Voltage
Seconds
system be powered from an
uninterruptible power supply
Interruption
or a battery.
% U
T
>95
5
Power frequency magnetic
fields should be at levels
characteristic of a typical
location in a typical
commercial or hospital
environment.
1 1