Clarity CL-XL40D Посібник користувача

Переглянути онлайн або завантажити pdf Посібник користувача для Телефон Clarity CL-XL40D. Clarity CL-XL40D 2 сторінки. Amplified telephone with dcp

Друкувати сторінку

SECTION 6

INTRODUCTION TO CLARITYLOGIC

No Dial Tone/Phone Will Not Operate

ClarityLogic is the name of our simplified and easy to

1. Check all phone cords and connections. Make sure they are plugged in

use customer support service. While talking to a Clarity

securely.

representative, the telephone sends information such as its

2. Plug unit into a different phone jack to help determine if the difficulty is

with the phone or the phone jack.

model name and settings to Clarity. The representative is

3. Switch out handset or telephone line cords.

immediately aware of the type and current settings of the phone.

4. Disconnect any other equipment that may be attached to the phone.

This will allow any troubleshooting call to be quick and simple,

Unable To Dial Out

1. Make sure TONE/PULSE switch is set correctly.

helping you find exactly what you are looking for. Just call 1.877.

2. Phone may be at the end of a long line of phones (loop). Phone may not

LOGIC24 (1.877.564.4224) to find out how Clarity is there to

be getting enough power from the phone line. It may be necessary to wait

make life easier.

for a few seconds after lifting the handset to begin dialing.

3. The XL40D is not compatible with Digital PBX Systems. If a standard,

ClarityLogic® Memory Dial

single line phone works on the system, your XL40D should also.

For your convenience, Clarity has pre-programmed the customer

4. There is an advanced computer running inside the XL40D. Sometimes

support number into M1 of the phone. If you do not wish to

after the handset is picked up, it will take a little less than a second to

engage the phone. Since it is not immediate, if you dial a number before

have this number stored in your phone, any new number can be

the computer engages, it will not receive the entire phone number that is

programmed to that button.To do this, follow the directions in

dialed.

The Person On The Other End Cannot Hear You

the MEMORY STORAGE section of the User Guide.

1. Too many phones or phone devices on the line may effect your phone's

transmission. As a guideline, more than five (5) phones or phone devices

NOTE: ClarityLogic has been designed to work with plain old

may overload the phone line. Disconnect one (1) or two (2) devices to see

telephony service (POTS). If your phone service is provided by

if that eliminates the problem. If not, contact your local phone company

for load guidelines.

a broadband service provider, ClarityLogic may not work. ONLY

2. You may not be speaking directly into the transmitter. Always speak

CLARITYLOGIC MAY BE DISABLED. ALL OTHER FEATURES

directly into the mouth piece in your normal tone of voice.

Unable To Hear Phone Ringer

WORK AS DESCRIBED IN THIS USER GUIDE.

1. Too many phone or phone devices on a line may cause your phone to

SUBSCRIPTION DATA AND PRIVACY POLICY

not ring. Disconnect one (1) or two (2) of the devices to see if the

problem is eliminated. If not, contact your local phone company for load

Your device will automatically send Clarity various types of

guide lines.

information as part of the Clarity services, which may include the

2. If power is not being supplied to the phone, the extra loud ringer, will

phone number associated with your device. This information may be

not work.

combined with account and other information we have on record

3. Check the Ringer ON/OFF switch to see if the ringer is off.

regarding you or your device or may be transmitted to us by your

Volume Control Does Not Work

device. To assist with remote diagnostics and other customer services

1. BOOST must be activated to turn on the additional amplification.

functions, your device may also regularly send us certain information

2. Check power connections. BOOST will not work without power or

associated with your device, including software and hardware settings,

backup batteries.

the phonebook, caller ID history and other information you have

Unable to Access Automated Systems

stored on the device. All of such information, together with other

Automated systems used by banks, long distance voice mail and other

information that we have on record regarding you and your device

applications require that a phone be set to "TONE" dialing. Check the switch

on the bottom of the phone labeled TONE/PULSE and set to TONE. This

is collectively referred to as the "Subscription Data". We use this

will enable the phone to be compatible with these automated systems.

information to diagnose and troubleshoot any device issues as well as

to provide you with the Services.

If the power goes out, or the AC Adapter is not properly connected to

You agree that Clarity and its subsidiaries, affiliates, partners, suppliers,

the phone, the amplification, extra loud ringer, and the lighted keypad will

and agents (collectively, "Affiliates") may collect, store, access,

not work. If you have backup batteries installed, amplification will still work,

disclose, transmit, process, and otherwise use your Subscription

but the phone will drain the backup batteries very quickly. This will cause the

Data to provide you with the Clarity services, address your requests,

need for the batteries to be changed frequently and the Low Battery indicator

provide technical support, process transactions for your account,

light to constantly illuminate.

and otherwise use such Subscription Data in accordance with

Do I Need to Install Batteries? Batteries are optional. They provide

Clarity's privacy policy (http://www.clarityproducts.com/privacy.

backup in case of a power outage. They are recommended in areas of

asp), which is hereby incorporated by reference. Clarity may also

frequent power outages. This phone uses four (4) alkaline batteries. When

provide or enable certain Services through your Device that rely

installed and fully charged, the batteries maintain the high amplification for

upon location information. In order to provide such Services, Clarity

your telephone.

and its Affiliates may collect, store, access, disclose, transmit, process,

and otherwise use your location data (including real time geographic

Still Not Working? If, after going through this checklist, the

Information) in accordance with Clarity's privacy policy.

XL40DD is still not functioning properly, call ClarityLogic at 1.877.

LOGIC24 (1.877.564.4224).

SECTION 7

SECTION 8

TROUBLESHOOTING

IMPORTANT SAFETY INSTRUCTIONS

When using your telephone equipment, basic safety precautions should always

be followed to reduce the risk of fire, electric shock and injury to persons

including the following:

1. Read and understand all instructions.

2. Follow all warnings and instructions marked on the telephone.

3. Do not use this telephone near a bathtub, wash basin, kitchen sink or laundry

tub, in a wet basement, near a swimming pool or any where else there is water.

4. Avoid using a telephone (other than a cordless type) during a storm. There

may be a remote risk of electrical shock from lightning.

5. Do not use the telephone to report a gas leak in the vicinity of the leak.

6. Unplug this telephone from the wall outlets before cleaning. Do not use

liquid cleaners or aerosol cleaners on the telephone. Use a damp cloth for

cleaning.

7. Place this telephone on a stable surface. Serious damage and/or injury may

result if the telephone falls.

8. Do not cover the slots and openings on this telephone. This telephone

should never be placed near or over a radiator or heat register. This telephone

should not be placed in a built-in installation unless proper ventilation is

provided.

9. Operate this telephone using the electrical voltage as stated on the base unit

or the owner's manual. If you are not sure of the voltage in your home, consult

your dealer or local power company.

10. Do not place anything on the power cord. Install the telephone where no

one will step or trip on the cord.

11. Do not overload wall outlets or extension cords as this can increase the

risk of fire or electrical shock.

12. Never push any objects through the slots in the telephone. They can touch

dangerous voltage points or short out parts that could result in a risk of fire or

electrical shock. Never spill liquid of any kind on the telephone.

13. To reduce the risk of electrical shock, do not take this phone apart.

Opening or removing covers may expose you to dangerous voltages or other

risks. Incorrect reassembly can cause electric shock when the appliance is

subsequently used.

14. Unplug this product from the wall outlet and refer servicing to the

manufacturer under the following conditions: when the power supply cord

or plug is frayed or damaged.; if liquid has been spilled into the product; if

the telephone has been exposed to rain or water; if the telephone does not

operate normally by following the operating instructions. adjust onlythose

controls that are covered by the operating instructions. Improper adjustment

may require extensive work by a qualified technician to restore the telephone

to normal operation.; if the telephone has been dropped or the case has been

damaged; if the telephone exhibits a distinct change in performance.

15. Never install telephone wiring during a lightning storm.

16. Never install telephone jacks in wet locations unless the jack is specifcally

designed for wet locations.

17. Never touch uninsulated telephone wires or terminals unless the tele

phone line has been disconnected at the network interface.

18. Use caution when installing or modifying telephone lines.

BATTERY SAFETY INFORMATION

Dispose of used batteries according to the instructions.

1. Do not dispose of the battery in a fire as it may explode. Check with local codes

for possible special disposal instructions.

2. Do not open or mutilate the battery. Released electrolyte is corrosive and may

cause damage to the eyes and skin. It may be toxic if swallowed.

3. Exercise care in handling batteries in order not to short the battery with

conducting materials such as rings, bracelets and keys. The battery or conduction

material may overheat and cause burns.

SECTION 9

REGULATORY COMPLIANCE

Part 68 of FCC Rules Information

Part 15 of FCC Rules Information

a) This equipment complies with Part 68 of the FCC rules and the

This device complies with Part 15 of the FCC Rules. Operation is subject to the

requirements adopted by the ACTA. On the bottom of this equipment is a

following two conditions: (1) This device may not cause harmful interference, and (2)

this device must accept any interference received, including interference that may

label that contains, among other information, a product identifier in the format

cause undesired operation.

US:AAAEQ##TXXXX. If requested, this number must be provided to the

telephone company.

Your equipment has been tested and found tocomply with the limits of a Class B

digital device, pursuant to Part 15 of FCC rules. These limits are designed to provide

b) A plug and jack used to connect this equipment to the premises wiring

reasonable protection against harmful interference in residential installation.

and telephone network must comply with the applicable FCC Part 68 rules

and requirements adopted by the ACTA. A compliant telephone cord and

This equipment generates, uses and can radiate radio frequency energy and, if not

modular plug, RJ11C USOC, is provided with this product. It is designed to be

installed and used in accordance with the instructions, may cause harmful interference

to radio communications. However, there is no guarantee that interference will not

connected to a compatible modular jack that is also compliant. See installation

occur in a particular installation; if this equipment does cause harmful interference to

instructions for details.

radio or television reception, which can be determined by turning the equipment off

c) The REN is used to determine the number of devices that may be

and on, you are encouraged to try to correct the interference by one of the following

connected to a telephone line. Excessive RENs on a telephone line may result

measures:

in the devices not ringing in response to an incoming call. In most but not

1. Where it can be done safely, reorient the receiving television or radio antenna.

all areas, the sum of RENs should not exceed five (5.0). To be certain of the

number of devices that may be connected to a line, as determined by the total

2. To the extent possible, relocate the television, radio or other receiver with respect

RENs, contact the local telephone company. For products approved after July

to the telephone equipment. (This increases the separation between the telephone

23, 2001, the REN for this pro-duct is part of the product identifier that has

equipment and the receiver.)

the format US:AAAEQ##TXXXX.

3. Connect the telephone equipment into an outlet on a circuit different from that to

which the television, radio, or other receiver is connected.

The digits represented by ## are the REN without a decimal point (e.g., 03 is

a REN of 0.3). For earlier products, the REN is separately shown on the label.

4. Consult the dealer or an experienced Radio/TV Technician for help.

d) If this telephone equipment causes harm to the telephone network, the

CAUTION: Changes or modifications not expressly approved by the manufacturer

telephone company will notify you in advance that temporary discontinuance

responsible for compliance could void the user's authority to operate the equipment.

of service may be required. But if advance notice isn't practical, the telephone

company will notify the customer as soon as possible. Also, you will be advised

Industry Canada Technical Specifications

of your right to file a complaint with the FCC if you believe it is necessary.

This product meets the applicable Industry Canada technical

e) The telephone company may make changes in its facilities, equipment,

specifications.

operations or procedures that could affect the operation of the equipment. If

this happens the telephone company will provide advance notice in order for

Before installing this equipment, users should ensure that it is per- missible to be

you to make necessary modifications to maintain uninterrupted service.

connected to the facilities of the local telecommunications company. The equipment

f) If trouble is experienced with this telephone equipment, for repair or

must also be installed using an acceptable method of connection. In some cases,

warranty information, please contact Clarity, 1-800-552-3368. If the equipment

the company's inside wiring associated with a single line individual service may be

is causing harm to the telephone network, the telephone company may

extended by means of a certified connector assembly (telephone extension cord). The

request that you disconnect the equipment until the problem is resolved.

customer should be aware that compliance with the above conditions may not prevent

degradation of service in some situations. Repairs to certified equipment should be

g) This telephone equipment is not intended to be repaired and it contains no

made by an authorized Canadian maintenance facility designated by the supplier.

repairable parts. Opening the equipment or any attempt to perform repairs

Any repairs or alterations made by the user to this equipment, or equipment

will void the warranty. For service or repairs, call 1-800-552-3368.

malfunctions, may give the telecommunications company cause to request the user to

h) Connection to party line service is subject to state tariffs. Contact the

disconnect the equipment.

state public utility commission, public service commission or corporation

Users should ensure for their own protection that the electrical ground connections

commission for information.

of the power utility, tele-phone lines and internal metallic water pipe system, if present,

are connected together. This precaution may be particularly important in rural areas.

i) If your home has specially wired alarm equipment connected to the

CAUTION: Users should not attempt to make such connections themselves,

telephone line, ensure the installation of this telephone equipment does not

but should contact the appropriate electrical inspection authority, or electrician, as

disable your alarm equipment. If you have questions about what will disable

appropriate.

alarm equipment, consult your telephone company or a qualified installer.

The Ringer Equivalence Number is an indication of the maximum number of terminals

j) This telephone equipment is hearing aid compatible.

allowed to be connected to a telephone interface. The termination on an interface may

Customer-Owned Coin/Credit Card Phones:

consist of any combination of devices subject only to the requirement that the sum of

To comply with state tariffs, the telephone company must be given notification

the Ringer Equivalence Numbers of all the devices does not exceed five.

prior to connection. In some states, the state public utility commission, public

(The term "IC:" before the certification/registration number only signifies that the

service commission or corporation commission must give prior approval of

Industry Canada technical specifications were met.)

connection.

The party responsible for regulatory compliance:

Clarity, A Division of Plantronics, Inc.

4289 Bonny Oaks Drive, Suite 106

Chattanooga, TN 37406

Phone: 1-800-564-4224

SECTION 10

REGULATORY COMPLIANCE

WARRANTY SERVICE INFORMATION

The following warranty and service information applies only to products

purchased and used in the U.S. and Canada. For warranty information in other

countries, please contact your local retailer or distributor.

Limited Warranty: Clarity, a division of Plantronics, Inc. ("Clarity") warrants to

the original consumer purchaser that, except for limitations and exclusions set

forth below, this product shall be free from defects in materials and workmanship

for a period of one (1) year from the date of original purchase ("Warranty

Period"). The obligation of Clarity under this warranty shall be at Clarity's option,

without charge, of any part or unit that proves to be defective in material or

workmanship during the Warranty Period.

Exclusions from Warranty: This warranty applies only to defects in factory

materials and factory workmanship. Any condition caused by accident, abuse,

misuse or improper operation, violation of instructions furnished by Clarity,

destruction or alteration, improper electrical voltages or currents, or repair or

maintenance attempted by anyone other than Clarity or an authorized service

center, is not a defect covered by this warranty. Telephone companies manufacture

different types of equipment and Clarity does not warrant that its equipment is

compatible with the equipment of a particular phone company.

Implied Warranties: Under state law, you may be entitled to the benefit of

certain implied warranties. These implied warranties will continue in force only

during the warranty period. Some states do allow limitations on how long an

implied warranty lasts, so the above limitation may not apply to you.

Incidental or Consequential Damages: Neither Clarity nor your retail dealer

or selling distributors has any responsibility for any incidental or consequential

damages including without limitation, commercial loss or profit, or for any

incidental expenses, expenses, loss of time, or inconvenience. Some states do not

allow exclusion or limitation of incidental or consequential damage, so the above

limitation or exclusion may not apply to you.

Other Legal Rights: This warranty gives you specific legal rights and you may

also have other rights which vary from state to state.

To obtain warranty service, please prepay shipment and return the unit to the

appropriate facility listed below.

Clarity Service Center,

4289 Bonny Oaks Drive, Suite 106,

Chattanooga, Tennessee 37406

Tel. (423) 629-3500 or (800) 552-3368;

Fax: (423) 622-7646 or (800) 325-8871

Plantronics Service Center,

8112 Trans Canada Highway,

Ville Saint-Laurent, Quebec H4S 1M5

Tel: (800) 540-8363 or (514) 956-8363,

Fax: (514) 956-1825

Please use the original container, or pack the unit(s) in a sturdy carton with

sufficient packing material to prevent damage. Include the following information:

A proof-of-purchase indicating model number and date of purchase;

Bill-to address;

Ship-to address.;

Number and description of units shipped;

Name and telephone number of person to call, should contact be necessary.;

Reason for return and description. of the problem.

Damage occurring during shipment is deemed the responsibility of the carrier, and

claims should be made directly with the carrier.

SECTION 11