eControls Comfort365 C365T11 Посібник користувача та інструкція з встановлення - Сторінка 7

Переглянути онлайн або завантажити pdf Посібник користувача та інструкція з встановлення для Протипожежні та протидимні клапани eControls Comfort365 C365T11. eControls Comfort365 C365T11 13 сторінок.
Також для eControls Comfort365 C365T11: Посібник користувача (4 сторінок), Посібник користувача (4 сторінок), Посібник користувача та інструкція з встановлення (13 сторінок), Посібник користувача та інструкція з встановлення (13 сторінок), Посібник користувача та інструкція з встановлення (13 сторінок), Встановлення (2 сторінок)

Друкувати сторінку
eControls Comfort365 C365T11 Посібник користувача та інструкція з встановлення
04 Compressor Minimum
Off Time
Factory Default: 2 Min. Range: 0 to 9 Min.
Use the UP/DOWN
keys to change the
minimum off time
(minutes) before
restarting the
compressor.
Touch NEXT or ENTER.
05 Heating Minimum Off Time
Factory Default: 0 Min. Range: 0 to 9 Min.
Use the UP/DOWN
Option
keys to change the
minimum off time
(minutes) before
restarting a gas
furnace or electric
strip heater.
Touch NEXT or ENTER.
06 Minimum Run Time
Factory Default: 2 Min. Range: 0 to 9 Min.
Use the UP/DOWN
Option
keys to change the
minimum run time
(minutes) before
turning a system off.
Touch NEXT or ENTER.
07 Setting On-Off Temperature
Differential
Factory Default: #1. Range: 0, 1 or 2.
Use the UP/DOWN
keys to select 0, 1,
2.
Touch NEXT or
ENTER.
o
Differential Mode0
0.5 On/Off Span.
o
Differential Mode1
1.0 On/Off Span.
o
Differential Mode2
1.5 On/Off Span.
08 Smart Recovery
Factory Default: Off. Range: On or Off.
Smart recovery initiates a heating or cooling call
so that the space is at temperature when the
setback period ends.
Use the UP key to
Option
select ON to turn on
smart recovery or
the DOWN key to
select OF to turn
smart recovery off.
Touch NEXT or ENTER.
INSTALLER SECTION
09 Vacant Heating Setpoint
Factory Default: 65 F.
Use the UP/DOWN
keys to select the
Option
heating temperature
when the space is
vacant.
NEXT
ENTER
Touch NEXT or ENTER.
10 Vacant Cooling Setpoint
Factory Default: 80 F.
Use the
UP/DOWN
keys to select the
cooling temperature
when the space is
vacant.
Touch NEXT or ENTER.
NEXT
ENTER
11 Calibrating Living Area
Temperature Sensor
Factory Default: None.
Use the UP/DOWN
keys to change the
Living area
temperature to the
temperature that the
user feels is correct.
Touch NEXT or ENTER.
NEXT
ENTER
12 Calibrating Sleeping Area
Temperature Sensor
Factory Default: None.
Use the UP/DOWN
keys to change the
Sleeping area
temperature to the
Option
temperature that the
user feels is correct.
Touch NEXT or ENTER.
NEXT
ENTER
13 Airflow Update Time
Factory Default: 2 Min. Range: 1 to 20 Min.
This is the frequency, in minutes, that the damper
position is updated.
Use the
UP/DOWN
keys to set the time
in minutes to update
the sleeping and
living area airflow.
Touch NEXT or ENTER.
NEXT
ENTER
o
o
o
Range: 44 F to 75 F
Option
Heat
Vacant
NEXT
ENTER
o
o
o
Range: 74 F to 95 F
Option
Cool
Vacant
NEXT
ENTER
o
Range - +/-5
Option
Living
NEXT
ENTER
o
Range - +/-5
Option
Sleeping
NEXT
ENTER
Option
NEXT
ENTER
Page 7 of 16
14 Night Level LCD Backlight
Factory Default: On. Range: On or Off.
The LCD has a low
Option
level backlight that
can be used as a
Night
night light.
Use the
UP
key to
turn the low level
backlight ON or touch the
DOWN
OFF.
Touch NEXT or ENTER.
15 Airflow Control, On or Off
Factory Default: On. Range: On or Off.
This option turns the automatic airflow control on
or off. If off, the dampers fully open, nighttime
airflow options are disabled and airflow is no
longer displayed on the thermostat.
Use the
UP
key to
Sleeping
Option
select ON for airflow
Airflow %
control or touch the
Living
DOWN
key to select
OFF to disable
airflow control.
Touch NEXT or ENTER.
If Airflow Control was off and is now being turned on,
the Nighttime Airflow option can be turned on using the
User Options.
16 User (Manual) Airflow Control
Enabled
Factory Default: On. Range: On or Off.
Manual airflow control enables the homeowner
to direct more airflow to the living or sleeping
space as they desire. This option is ideal for
homeowners who have an unusual work
schedule, home office or spend more time in one
space than the other. The User Menu is used to
turn off automatic airflow control. Nighttime
Airflow option is still enabled but can be turned
off using the User Options.
Use the
DOWN
key
Option
to select OFF only if
disabling manual
airflow control. (Not
typical)
Touch NEXT or ENTER.
NEXT
ENTER
key to turn
NEXT
ENTER
NEXT
ENTER