ALDI 54731 Посібник користувача - Сторінка 9

Переглянути онлайн або завантажити pdf Посібник користувача для Дриль. ALDI 54731. ALDI 54731 16 сторінок. 24v lithium-ion cordless drill with hammer action & 2 x batteries

Друкувати сторінку

Battery Fitting / Battery Charging

Fitting and removing the battery pack

1. To install the battery pack (9) to the tool, align the raised portion of the

battery pack (9) with the grooves on the bottom of the drill/driver, and

with your thumb on the battery release tab (16), slide it firmly into the

handle until the battery is secure in position (Fig A). Release your thumb

from the battery release tab (16).

2. To remove the battery pack from the tool, press the battery pack release

button (16) and slide the battery pack completely out of tool handle

(Fig B).

3. When applying the charger adaptor (10) onto the battery pack (9), slide

the charger adaptor (10) onto the battery pack (9), whilst aligning the

tabs on the battery pack (9) with the tabs on the charger adaptor (10)

(Fig C).

The charger adaptor (10) will make a snap / click noise when it is

securely aligned.

4. To remove the battery pack (9) from the charger adaptor (10), press the

battery release button (16) and slide the charger adaptor backwards

/ outwards, opposite to the direction it was installed into the charger

adaptor (10).

Battery charging

IMPORTANT. Before attempting to charge the battery, check the charger

adaptor (10), plug pack charger (11), and the battery to ensure the charging

equipment matches the battery supplied. The components are all labelled

with component numbers.

Check the input voltage on the charger label and ensure the input voltage

indicates 100-240V ac 50-60 Hz.

e-mail: [email protected]

MODEL: №. 2024001 • 02/2017 • 55945

24v Lithium-ion Cordless Drill with Hammer Action

AFTER SALES SUPPORT

1800 909 909

(toll free)

24v Lithium-ion Cordless Drill with Hammer Action

CAUTION! The rechargeable battery may not be fully charged on leaving

the factory. Charge the rechargeable battery for approx 3-5 hours before first

use, or until fully charged.

If the battery pack (9) does not accept a charge when first plugged in and

connected, ie the red light does not come on, the battery pack is most likely

fully charged from the factory.

In this case it is suggested to use or run the drill for a few minutes and then re

connect to the charger. The red charging light should come on showing the

charging cycle is working correctly.

CAUTION! The working temperature of the charging operation is 0°C to 45°C.

1. Connect the power supply from the plug pack charger (11) to the charger

adaptor (10) via plugging the plug from the plug pack charger (11) into the

charger adaptor (10) housing.

Plug in the plug pack charger (11) and switch on at the power supply. The

light on the plug pack charger (11) will highlight "green" to indicate there is

power (Fig D).

2. Align the battery (9) with the charger adaptor (10). Insert the battery pack

and slide it firmly into position (Fig C). The light on the plug pack charger

will highlight "red" to indicate the battery is being charged (Fig E).

The battery will be ready for use up to approximately 3-5 hours.

When the battery is charged to the correct voltage the red changes to

GREEN indicating the plug pack is still connected to the turned on power

but is NOT charging

NOTE: The power to the charger should be turned off when unattended, with

or without a battery inserted.

AFTER SALES SUPPORT

1800 909 909

(toll free)

Speeds

e-mail: [email protected]

MODEL: №.2024001 • 02/2017 • 55945