Zanussi ZRB 230 Інструкція з експлуатації - Сторінка 7

Переглянути онлайн або завантажити pdf Інструкція з експлуатації для Холодильник Zanussi ZRB 230. Zanussi ZRB 230 8 сторінок. Refrigerator- freezer combination

Друкувати сторінку

Instructions for the Installer

Technical data

Installing the appliance

Transportation, unpacking

It is recommended to deliver the appliance in

original packaging, in vertical position

considering the protective warning on packaging.

After each transportation the appliance must not

be switched on for approx. 2 hours.

Unpack the appliance and check if there are

damages on it. Report possible damages

immediately to the place you bought it. In that

case retain packaging.

Cleaning

Remove every adhesive tape and everything else,

which ensure the accessories not to move in the

appliance.

Wash the inside of the appliance using lukewarm

water and mild detergent. Use soft cloth. After

cleaning, wipe out the inside of the appliance.

Placement

The ambient temperature has an effect on the

energy consumption and proper operation of the

appliance. When placing, take into consideration

that it is practical to operate the appliance

between ambient temperature limits according

to the climate class that is given i

the chart below and can be found in the data label.

If the ambient temperature goes below the lower

data the temperature of the cooling compartment

can go beyond the prescribed temperature.

If the ambient temperature goes beyond the upper

data this means longer operating time of the

compressor, breakdown in the automatic

defrosting increasing temperature in the cooling

compartment or increasing energy consumption.

When placing the appliance ensure that it stands

level. This can be achieved by two adjustable feet

(1) at the bottom in front.

How to save energy

Avoid pulling the appliance in a sunny place and

near anything that gives off heat.

Be sure that the condenser and the compressor

are well ventilated. Do not cover the sections

where ventilation is.

Wrap products in tightly closing dishes or cling

film to avoid building up unnecessary frost.

Do not leave the door open longer than

necessary and avoid unnecessary openings.

Put warm foods into the appliance when they are

at room temperature.

Keep the condenser clean.

The appliance and environment

This appliance does not contain gasses which

could damage the ozone layer, in either its

refrigerant circuit or insulation materials. The

appliance shall not be discarded together with the

urban refuse and rubbish. Avoid damaging the

cooling unit, especially at the rear near the heat

exchanger. Information on your local disposal

sites may be obtained from your municipal

authorities.

The materials used on this appliance marked with

the

symbol are recyclable.

Maintenance

Defrosting

Bleeding part of the moisture of cooling chambers

in form of frost and ice goes with the operation of

the appliance.

Thick frost and ice has an insulating effect, so it

reduces cooling efficiency as the temperature

increases in the cooling chambers and they need

more energy.

At this type of appliance defrosting the cooling

plate of the refrigerator is automatic without any

external intervention. The thermostatic control

interrupts the operation of compressor at regular

intervals for more or less time during this cooling

is interrupted the temperature of the cooling plate

goes above 0 °C due to interior heating load of the

compartment, so defrosting occurs. When the

surface temperature of the cooling plate has

reached +3 - +4 °C the thermostatic control

restarts operation of the system.

Melting water flows through defrost water outlet

leaded through the back into the evaporative tray

maintained on the top of compressor and

evaporates due to its warmth.

Check and clean the outlet of melting water

coming during defrosting regularly

a label inside the appliance warns you for

this. If it is clogged the melting water

gathered can cause earlier failure as it can

go to the insulating of the appliance.

Clean the melting water outlet with the supplied

pipe scraper that can be seen in the figure above.

The pipe scraper has to be stored in the outlet.

The most typical case of clogging up in the

melting water outlet when you put food wrapped

in some paper into the appliance and this paper

contacts back plate of the refrigerator and freezes

to it. If you remove the food right at this moment

the paper will tear and it can cause clogging up in

the outlet by gelling into it.

So you are asked to be careful because of the

above when placing foods wrapped in paper into

the appliance. In case of increased demand e.g.

during heat waves, the refrigerator temporarily

happens to operate constantly. During this the

automatic defrosting is ineffective.