Directed Xpresskit DBALL2 Посібник з монтажу - Сторінка 18

Переглянути онлайн або завантажити pdf Посібник з монтажу для За замками Directed Xpresskit DBALL2. Directed Xpresskit DBALL2 20 сторінок. Ford5 remote start ready (rsr) installation
Також для Directed Xpresskit DBALL2: Посібник з монтажу (12 сторінок), Посібник з монтажу (19 сторінок), Посібник з монтажу (18 сторінок), Посібник (14 сторінок), Посібник з монтажу (13 сторінок), Посібник з монтажу (14 сторінок), Посібник з монтажу (19 сторінок), Посібник з монтажу (16 сторінок), Посібник з монтажу (15 сторінок), Посібник зі встановлення та короткий довідник (16 сторінок), Посібник з монтажу (18 сторінок), Посібник з монтажу (16 сторінок), Посібник з монтажу (18 сторінок), Посібник з монтажу (16 сторінок), Посібник (19 сторінок)

Друкувати сторінку
Directed Xpresskit DBALL2 Посібник з монтажу

Quick Reference Guide

Quick Reference Guide
DBALL2-FORD3 Remote Start Ready (RSR) Installation
Vehicle Takeover with Get In and Go*
Close the vehicle doors, hood and trunk, then press
1
the Remote Start button on the transmitter to start
the vehicle.**
Press the Unlock button on the factory
2
or aftermarket remote.**
Complete the following steps within 45 seconds
or the vehicle will shut down.
Enter the vehicle, while making sure the
3
factory remote is inside with you.
Press the brake pedal, put the car
4
in gear and drive off.
* Get In and Go connections required.
** Your aftermarket remote may differ from the model shown in the illustrations.
Get In and Go
Get In and Go is designed to provide users with easy takeover when
GG
entering their Push-to-Start (PTS) equipped vehicle, once it has been
remote started.
Typically, users would have to remote start their vehicle, then get inside and press
the vehicle start button to perform a takeover. There is therefore a physical action
required to drive away. With Get In and Go technology, you simply remote start the
vehicle, unlock the doors, get in and go... Nothing to do but put the gear in drive and
enjoy your vehicle.
This unique feature monitors a variety of parameters such as the key fob, vehicle
speed sensor and door sensor, in order to perform takeover securily.
GG
Press
remote start
button**
Press Unlock
OR
button on
either remote**
Enter vehicle
with key fob
Ready to
drive off
Pit Stop Mode
The Pit Stop Mode feature is practical when you need to stop and run an errand,
but wish to keep the engine running.
Stop the vehicle in a safe parking spot
1
and put the gear in Park (P).
2
Press the button to remote start the vehicle.*
It is now safe to leave the engine running and exit the
vehicle with the Smart Key in hand.
3
Note: We recommend that you always lock the doors
of your vehicle when leaving it unattended.
* Your aftermarket remote may differ from the model shown in the illustrations.
Parking Light Error Codes
The parking lights on your vehicle will flash a specific number of times 3 seconds
following an unscheduled shutdown or failure to start. Each flashing pattern is
described below.
Flashes
Diagnostic
1
Runtime expired.
2
Over-rev shutdown.
3
Low/No RPM.
4
Transmitter shutdown.
5
Brake shutdown.
6
Hood shutdown/Remote start safety override switch is ON*.
7
Remote start safety override switch is ON*.
* If the vehicle hood status is supported through data, it will also report a 7 flash
safety override code.
P
&
Stop & put vehicle in Park (P)
Press
remote start
button*
Exit vehicle with
Smart Key
© 2017 Directed. All rights reserved.