Directed Xpresskit DBALL2 Посібник з монтажу - Сторінка 13

Переглянути онлайн або завантажити pdf Посібник з монтажу для За замками Directed Xpresskit DBALL2. Directed Xpresskit DBALL2 18 сторінок. Ford5 remote start ready (rsr) installation
Також для Directed Xpresskit DBALL2: Посібник з монтажу (12 сторінок), Посібник з монтажу (19 сторінок), Посібник з монтажу (18 сторінок), Посібник (14 сторінок), Посібник з монтажу (13 сторінок), Посібник з монтажу (14 сторінок), Посібник з монтажу (19 сторінок), Посібник з монтажу (16 сторінок), Посібник з монтажу (20 сторінок), Посібник з монтажу (15 сторінок), Посібник зі встановлення та короткий довідник (16 сторінок), Посібник з монтажу (18 сторінок), Посібник з монтажу (16 сторінок), Посібник з монтажу (16 сторінок), Посібник (19 сторінок)

Друкувати сторінку
Directed Xpresskit DBALL2 Посібник з монтажу
Platform: DBALL2
Firmware:
CHRYSLER Remote Start Ready
LED
Description
External module synchronization
OBDII feature is not supported.
(Flashes red,
red then
orange) x 10
Activation Ground When Running (Status)
Flashes
Ground When Running (Status) command received.
green
Ignition ON command received.
Flashes red
& orange
Flashes
Start ON command received.
green
quickly
Flashes red
PTS shutdown error.
x 10
Flashes red
CAN bus incorrectly detected.
x 21
Commands
Flashes
LOCK command received.
orange x 1
Flashes
UNLOCK command received.
orange x 2
Flashes
TRUNK command received.
orange x 3
Flashes
AUX1 command received.
orange x 4
Flashes
AUX2 command received.
orange x 5
Flashes
AUX3 command received.
orange x 6
Shutdown codes
Flashes
Takeover successful.
green x 1
Flashes red
Runsafe was not disabled.
x 1
Flashes red
Brake was not detected.
x 2
Flashes red
Smart key was not detected.
x 3
Flashes red
Speed was detected.
x 4
RSR codes
3x OEM Lock Remote Start Activation was attempted
Flashes red
x 7
when RFTD feature is disabled.
Flashes red
Feature error.
x 9
4
(RSR)
Installation
Troubleshooting
The diagnostic data bus was not detected, therefore the
SmartStart features will be limited.
The module has initialized the remote start sequence.
The module has received the Ignition ON command and
is processing the remote start sequence.
The module has received the Start ON command and is
processing the remote start sequence.
The PTS output from the module was not activated due
to safety protection.
Verify the CAN1 and CAN2 connections. Refer to
"Installation (wiring diagrams & vehicle wiring reference
charts)" to check the connections.
If the bypass module fails to flash, it did not receive the
signal. Commands can come from RF or D2D.
Normal operation.
No UNLOCK command was received prior to opening the
door, or the 45 second timer expired in takeover mode.
The brakes were not detected, which prevents the
system from shutting down the vehicle.
The smart key was not detected, which prevents the
system from shutting down the vehicle.
The vehicle was detected as moving, which prevents the
system from shutting it down.
Activated from Web automatically when using RSR flash
tool or can be done manually. Refer to feature
programing section for more information.
An RSR feature file mismatch was detected. Please
contact Technical Support.
Rev.: 20170817
Page 13
© 2017 Directed. All rights reserved.