Aleko LOCKMASTER L110C Посібник - Сторінка 16
Переглянути онлайн або завантажити pdf Посібник для Відкривач воріт Aleko LOCKMASTER L110C. Aleko LOCKMASTER L110C 17 сторінок.
Друкувати сторінку
ALEKO AC-2000 SLIDING GATE OPENER
11. Trouble Shooting
T
o r
u
b
e l
Motor only runs in one direction.
By pressing button 1(button 2 or button 3)
which has been programmed to open the
gate, press the same button again to stop
the gate in required position, but the gate
will auto-close immediately.
When you use button 4 of remote control
to open the gate, gate travels too short.
When you use button 4 of remote control
to open the gate, but the gate will auto-
close immediately.
The gate will not open or close.
Remote control does not work
When you open the gate by using button
1(button 2 or button 3) which has been
programmed, gate will stop in mid-travel
or reverse before reaching the fully limit
position.
The remote control operating distance is
too short.
The gate opens, but stops and will not
return.
P
o
s
s
b i
e l
c
a
u
s
e
The wire connector terminal block
becomes loose.
The limit switch wire connector terminal
block becomes loose.
The electric component on the control
board such as Q2, Q91 or Q92 may be
damaged.
The auto-close time is too short.
The width of pedestrian mode is too
narrow.
The auto-close time of pedestrian mode
is too short.
The limit switch wire connector terminal
block becomes loose.
Connecting wires or terminal blocks are
too loose.
The electric component on the control
board such as Q2, Q91 or Q92 may be
damaged.
P
o
w
r e
s
w
c t i
h
s i
O
F
F
The indicator light of remote control does
not light.
Remote control is not suitable for
receiver.
Broken receive board
The Force Adj. (VR1) is adjusted too
small.
G
a
e t
s i
o
b
t s
u r
c
e t
. d
Signals are shielded by the gate.
1. Please note the two magnet brackets
(fixed plate) are different: one is higher
and another is lower. Please try to
exchange the two brackets position.
2. Please try to exchange the limit switch
wires CL (close) and OP (open).
14
s
Check wire connector terminal block make
sure it is plugged in terminal block 10 (X8).
Check limit switch wire connector terminal
block make sure it is plugged in terminal
block 9 (X9).
Check the limit switch mode.
Replace the electric component Q2, Q91 or
Q92 (BTA16/600) or replace the board.
Reset the auto-close time. See Set auto-
close function section.
Reset the width of pedestrian mode. See Set
width of pedestrian mode section.
Reset the auto-close time of pedestrian. See
Set auto-close function of pedestrian
mode section.
Check the limit switch mode (see table 1 DIP
switch).
Check the connecting wires and terminal
blocks.
Replace the electric component Q2, Q91 or
Q92 (BTA16/600) or replace the board.
M
a
k
e
s
u
e r
p
Check the batteries on your remote control.
After making sure the codes are correct,
erase remote controls and then re-program
the codes in the device. See Adding extra
remote controls (learning) section.
Replace receive board.
Check the Force Adj. (VR1). Adjust VR1 to
increase force.
R
e
m
o
v
e
h t
e
Link a new antenna (1~1.2m BVR 0.75mm
see parts list) to the old antenna. Then fix the
antenna on the wall vertically, make sure the
total height from the top of antenna to the
ground is approx. 1.5m.
There are two reed switches inside the
magnetic limit switch: one is upper and
another is lower. Maybe the magnet position
was installed in the middle so it inducts both
reed switches. Solution: adjust the magnet
upper or lower.
S
l o
t u
o i
n
s
o
w
r e
s
w
c t i
h
s i
O
. N
o
b
t s
u r
t c
o i
. n
2