Clarke WOODWORKER CDS1 Інструкція з експлуатації та обслуговування - Сторінка 5

Переглянути онлайн або завантажити pdf Інструкція з експлуатації та обслуговування для Шліфувальна машина Clarke WOODWORKER CDS1. Clarke WOODWORKER CDS1 6 сторінок. Detail sander

Друкувати сторінку

Parts List

I
tem
Part No
Description
1
GRCDS1001
Cable
2
GRCDS1002
Cable Support
3
GRCDS1003
Screw
4
GRCDS1004
Cable Grip
5
GRCDS1005
Brush Holder
6
GRCDS1006
Brush Lining
7
GRCDS1007
Spring
8
GRCDS1008
Carbon Brush
9
GRCDS1009
Governor
10
GRCDS1010
Switch
11
GRCDS1011
Pusher
12
GRCDS1012
Right Housing
13
GRCDS1013
Nameplate 1
14
GRCDS1014
Screw
15
GRCDS1015
Circuit Board
16
GRCDS1016
Stator
17
GRCDS1017
Bearing
18
GRCDS1018
Rotor
19
GRCDS1019
Bearing
20
GRCDS1020
Pin
21
GRCDS1021
Small Gear
22
GRCDS1022
Nut
Accessories
A wide range of accessories is available from your nearest CLARKE dealer, for further
information, contact your nearest dealer, or telephone CLARKE International Sales
department on 01992 565300.
PARTS & SERVICE TEL: 020 8988 7400
or
e-mail as follows:
SERVICE:
-7-
Qty Item
Part No
Description
23
GRCDS1023
Bearing
1
1
24
GRCDS1024
Large Gear
2
25
GRCDS1025
Output Shaft
1
26
GRCDS1026
Pin
2
27
GRCDS1027
Bearing
2
28
GRCDS1028
Back Support
2
29
GRCDS1029
Fore Support
2
30
GRCDS1030
Eccentric Wheel
1
31
GRCDS1031
Bearing
32
GRCDS1032
Bushing
1
2
33
GRCDS1033
Spring
1
34
GRCDS1034
Grinding Head
1
35
GRCDS1035
Screw
2
36
GRCDS1036
Grinding Plate
1
37
GRCDS1037
Gasket
1
38
GRCDS1038
Screw
1
39
GRCDS1039
Felt Layer
1
40
GRCDS1040
Screw
1
41
GRCDS1041
Sanding Paper
42
GRCDS1042
Screw
1
1
43
GRCDS1043
Nameplate 2
1
44
GRCDS1044
Left Housing
14. ALWAYS wear proper apparel. loose clothing or jewellery may
get caught in moving parts. wear protective hair covering to
contain long hair.
Qty
15. ALWAYS use recommended accessories. the use of improper
accessories could be hazardous.
1
16. ALWAYS remove plug from electrical outlet when adjusting,
changing parts, or working on the machine.
1
1
17. NEVER operate machine while under the influence of drugs, alcohol or any medication.
1
18. NEVER leave machine running unattended. turn power off. Do
1
not leave the machine until it comes to a complete stop.
1
19. NEVER force the machine. it will do a better and safer job at
1
the rate for which it was designed.
1
20. NEVER use power tools in damp or wet locations or expose
1
them to rain. Keep your work area well illuminated. do not use
1
in explosive atmosphere (around paint, flammable liquids etc.).
Avoid dangerous environment.
1
1
Additional Precautions For Power Tools
4
1
1.
ALWAYS wear ear protectors/defenders as the noise level of this machine can exceed
1
85dB (A).
1
2.
ALWAYS use the appropriate sanding pads for the work being done. Replacement
1
pads are available from your CLARKE dealer (see parts list for details).
3
3.
ALWAYS keep the mains cable well away from the machine and ensure an adequate
1
electrical supply is close at hand so that the operation is not restricted by the length of
9
the cable.
1
4.
ALWAYS switch the machine OFF immediately the task is completed.
1
5.
NEVER allow the ventilation slots in the machine to become blocked.
6.
DO NOT use the machine if the electric cable, plug or motor is in poor condition.
7.
DONOT exert pressure on the sander to stop quickly, allow it to stop normally.
Additionally, please keep these instructions in a safe place for future reference.

DUST EXTRACTION

The sander is provided with a dust extraction facility, where a vacuum extractor, or dust
bag (not supplied), may be connected to the outlet at the rear of the machine. Please
note however, that this does not preclude the user from wearing a face mask to prevent
the inhalation of dust particles.
It is an EEC requirement that a dust extraction facility be provided on power tools, however,
due to the nature of the tool, some of the dust produced will be forced into the surrounding
atmosphere, and will not be collected.
-4-