CTS CVT-3002-PLUS-DR SERIES Посібник користувача

Переглянути онлайн або завантажити pdf Посібник користувача для Конвертер мультимедіа CTS CVT-3002-PLUS-DR SERIES. CTS CVT-3002-PLUS-DR SERIES 2 сторінки. Standalone gigabit media converter
Також для CTS CVT-3002-PLUS-DR SERIES: Посібник користувача (2 сторінок)

Друкувати сторінку

Trademarks

CTS is a registered trademark of Connection Technology

Systems Inc.. Contents subject to revision without prior notice.

All other trademarks remain the property of their owners.

This publication may not be reproduced as a whole or in part, in

any way whatsoever unless prior consent has been obtained

from Connection Technology Systems Inc..

FCC Warning

The CVT-3002-PLUS-DR Series converters have been tested

and found to comply with the limits for a Class A digital device,

pursuant to Part 15 of the FCC Rules. These standards are

designed to provide reasonable protection against harmful

interference when these devices are operated in a commercial

environment. These devices generate, use, and can radiate

radio frequency energy and may cause harmful interference to

radio communications unless installed in accordance with this

User's Guide. Operation of these devices in a residential area

is likely to cause harmful interference which will make the user

responsible for the appropriate remedial action at his / her own

expense.

CE Mark Warning

These are Class A products. In a domestic environment these

products may cause radio interference in which case the user

will need to consider adequate preventative methods.

1. Checklist

The package should contain the following items:

- CVT-3002-PLUS-DR Media Converter

- AC-DC Power Adapter

- User's Guide

Please notify your sales representative immediately if any item

is missing or damaged.

2. Overview

CVT-3002-PLUS-DR is designed to meet the massive needs

for Gigabit network deployment and able to extend a copper

based Gigabit network via fiber cable. It is fully compliant with

IEEE 802.3, 802.3u, 802.3ab, 802.3z, and 802.3x standards.

It can be installed into a CVT Converter RACK. The installation

and operation procedures are simple and straightforward.

Operation status can be locally monitored through a set of

Diagnostic LED indicators located in the front panel.

Major Features:

- TP and Fiber Auto-Negotiation

- MDI/MDIX Auto-Crossover

- Flow Control and Back Pressure

- 9K bytes Jumbo Frame

- Store and Forward switching mechanism

- 2K MAC address

- Link Alarm

- 100/1000Mbps dual rate fiber uplink

3. Installation



Attach fiber cable from the CVT-3002-PLUS-DR to the fiber

network. The fiber connections must be matched – transmit

socket to receive socket.



Attach a UTP cable from the 10/100/1000Base-T network

to the RJ-45 port on the CVT-3002-PLUS-DR.



Connect the power adapter to the CVT-3002-PLUS-DR and

check that the Power LED lights up. The TX Link/Act and

F/O Link/Act LEDs will light up when all the cable

connections are satisfactory.

Figure 1. CVT-3002-PLUS-DR Dual Fiber Front Panel

Figure 2. CVT-3002-PLUS-DR WDM & SFP Front Panel

Figure 3. CVT-3002-PLUS-DR Converter Rear Panel

DIP SWITCH Setting

The default setting for PIN 1 and 6 is ON. The rest pins are

OFF.

Pin NO.

Function

TP Auto-Negotiation

Manual TP speed

Duplex mode

Flow Control

F/O mode

Link Alarm

Reserved

NOTE:

Before adjusting the configuration of the DIP Switch, the

power should be unplugged.

Before changing TP speed, duplex mode and flow

control setting, please make sure PIN 1 is set to OFF.

When TP speed is set to 10M or 100M manually, PIN 3 needs

to be turned OFF.



Under 1000Mbps, it supports full-duplex mode only.

OFF

Disable

Enable

10M

100M

N/A

1000M

Half

Full

Disable

Enable

Force

Auto

Disable

Enable