CTS CVT-3012SFP Посібник користувача

Переглянути онлайн або завантажити pdf Посібник користувача для Конвертер мультимедіа CTS CVT-3012SFP. CTS CVT-3012SFP 2 сторінки. 10/100/1000base-t to 1000base-x (sfp slot) standalone media converter
Також для CTS CVT-3012SFP: Посібник користувача (19 сторінок)

Друкувати сторінку

Trademarks

CTS is a registered trademark of Connection Technology

Systems Inc. Contents subject to revision without prior

notice.

All other trademarks remain the property of their owners.

This publication may not be reproduced as a whole or in

part, in any way whatsoever unless prior consent has been

obtained from Connection Technology Systems Inc.

FCC Warning

The CVT-3012SFP Series converters have been tested

and found to comply with the limits for a Class A digital

device, pursuant to Part 15 of the FCC Rules. These

standards are designed to provide reasonable protection

against harmful interference when these devices are

operated in a commercial environment. These devices

generate, use, and can radiate radio frequency energy and

may cause harmful interference to radio communications

unless installed in accordance with this User's Guide.

Operation of these devices in a residential area is likely to

cause harmful interference which will make the user

responsible for the appropriate remedial action at his / her

own expense.

CE Mark Warning

These are Class A products. In a domestic environment

these products may cause radio interference in which case

the user will need to consider adequate preventative

methods.

This is a

lead-free and

RoHS-compliant product.

1. Checklist

The carton should contain the following items:

CVT-3012SFP Converter

AC-DC Power Adapter

RJ-45 to DB-9 Serial Cable

User's Guide

Please notify your sales representative immediately if any

items are missing or damaged.

2. Overview

CVT-3012SFP is designed to meet the massive needs for

Gigabit network deployment and able to extend a copper

based Gigabit network via fiber cable to a maximum distance

up to 80KM.

CVT-3012SFP is fully compliant with IEEE802.3, 802.3u,

802.3ab & 802.3z standards. It can be installed into a CVT

Converter RACK. The installation & operation procedures

are simple and straightforward. Operation status can be

locally monitored through a set of Diagnostic LED indicators

on the front panel.

Features

10/100/1000Base-T to 1000BASE-X Converter

Standard: IEEE 802.3, 802.3u, 802.3ab & 802.3z

Interface: 1 x RJ-45 LAN connector

1 x RJ-45 Console Port

1 x SFP Slot

Auto-Negotiation in TP port

MDI/MDIX Auto-Crossover supported

LED: PWR, F/O Link Act, TP Link Act, TP/FDX, Speed,

COM, Status

Plug-and-Play installation

Support Link Alarm

Support Jumbo Frame (64-9728 Byte)

Note:

Under 10/100Mbps, CVT-3012SFP only supports

packet length from 64 to1532 Byte. Please make sure

that the total packet length is smaller than 1532 Byte

while Tag-VLAN is enabled.

Support Selectable ISP Ethernet Tag Type

3. Installation

Attach fiber cable from the CVT-3012SFP to the fiber

network. The fiber connections must be matched –

transmit socket to receive socket.



Attach a UTP cable from the 10/100/1000BASE-T

network to the RJ-45 port on the CVT-3012SFP.



Connect the power adapter to the CVT-3012SFP and

check that the Power LED lights up. The TP Link/Act

and F/O Link/Act LEDs will light up when all the cable

connections are satisfactory.



Attach one end of the RJ-45 to DB-9 serial cable to the

RJ-45 COM port on the front panel of the converter

Attach the other end to a PC or workstation serial port.

Run a terminal emulation program using the following

settings:

Emulation

VT-100/ANSI compatible

BPS

9600

Data bits

Parity

None

Stop bits

Flow Control None

Enable

Terminal keys

Figure 1. CVT-3012SFP Converter Front Panel

Figure 2. CVT-3012SFP Converter Rear Panel